thermodynamics project , Mechanical Engineering

Assignment Help:
ES 347 - Thermodynamics Project Assigned: 3/28/2013 Due: 4/25/2013
Problem specification
5 kg of air is contained in a piston-cylinder device, initially at a pressure of 2MPa and a specific volume of 0.08m3/kg. The air then expands, as an ideal gas, through a polytropic process, with variable values of n, to a final specific volume of 0.30m3/kg.
Objective:
Write a MATLAB code to solve for the pressure and temperature variation throughout the expansion process and to calculate the work and heat produced in the processes for variable values of n.
Procedure: 1. Begin by defining the temperature at the initial state and then define the temperature and
pressure at the final state. Sketch a rough graph of what the process looks like on P-v coordinates. Write out by hand the equations and steps you would take to determine the actual P, T, and v at all points along the process. Identify unknowns, equations, constants, and calculation orders.
2. Using your hand calculations as a guide, write a simple MATLAB m-file to calculate the properties at points along the process (minimum of 20 points, but should be a variable that can be changed) using one of the values of n (I recommend using n=1.5). Plot P-v and T-v diagrams for the process using MATLAB.
3. Calculate the work performed for the process by integrating the curve of pressure versus specific volume. Use the “trapezoidal area method” for calculating the integral.
4. Assume that the specific internal energy for the air in this problem can be defined as a function of temperature as follows:
??(??) = (1.0344 * 10-4) * ??2 + (6.4476 * 10-1) * ?? + (1.3727 * 102)
Add code to your MATLAB program to calculate the specific internal energy for the process
using the information of the pressure and specific volume at each state. 5. Using conservation of energy and the work calculated, determine the amount of heat
transferred for each process. 6. Write a loop in the code to analyze the different values of n, or run the code for the different
values of n asked for below.
Deliverables 1. Hand calculations that outline planned MATLAB code. 2. MATLAB code (m-file) that calculates the state variables P, v, T, and u for the defined
process, and that calculates the work and heat for each process. 3. On the same graph, plot of P-v for this process with 4 different values of n: 1, 1.4, 1.5, 1.8. 4. Plot of P-v and T-v for n=1.5 on a single graph. Use the function plotyy. 5. Table summarizing results of work and heat as a function of n. 6. A brief paragraph detailing what you learned in this exercise and how useful you think these
skills will be for your future as an engineer. This is not a BS question, I want you to provide me with useful information about your experience. If you didn’t learn anything here because you already are a pro at MATLAB, say that!
For your reference, I have uploaded the m-file example_xy.m as an example of MATLAB programming and showing you some of the things you will need and can use.
I am happy to review any code problems you have, but I will not be checking code on the night before the due date, and it might take me a day or two to get to debugging any code that you send me. Therefore, plan ahead!
I will discuss the “trapezoidal area method” in class during the week of 4/1/2013.

please follow instruction

Related Discussions:- thermodynamics project

Dual cycle of heat engine.., how to calculate the mean effective pressure o...

how to calculate the mean effective pressure of a dual cycle

Connected rod - part of combustion engine, Connecte d Rod: It is att...

Connecte d Rod: It is attached to piston at its small end by means of gudgeon pin. The big end bearing is connected to crank pin. It is made up of forged steel.

Calculate the torque, (a) Illustrate self-locking and self-energizing brake...

(a) Illustrate self-locking and self-energizing brakes. (b) The diameter of the drum is 250mm and the angle of contact is 90 o , If the operating force of 700 N is applied at th

Wrking cran, this is a problem for designing wrecking crane. there are 2 sc...

this is a problem for designing wrecking crane. there are 2 scenarios, one is when ball is held and one where its at maximum. i calculated the loads and now need to find the follow

Explain in detail about the large excavations, Explain in detail about the ...

Explain in detail about the Large excavations Large excavations required for construction of rafts may need dewatering, depending on the ground water flow and the choice of  a

Calculate the spindle speed by (a) hss tool (b) carbide tool, Calculate the...

Calculate the Spindle Speed by (a) HSS tool (b) Carbide Tool Calculate the spindle speed (N) if a C 20 steel job of 50 mm dia is to be turned by (a) HSS tool and (b) Carbide T

Calculate the shear stress , A hollow circular shaft has an internal diamet...

A hollow circular shaft has an internal diameter of 48 mm and an external diameter of 54 mm. Calculate the shear stress produced at the outer and inner surfaces of the shaft when t

Calculate strength coefficient - true stress and true strain, Calculate str...

Calculate strength coefficient: A copper specimen of 64 mm gauge length and 12.80 mm dia. was tested in tension. Following two diameters were recorded in the plastic range of

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd