Show the frequency response of rc coupled amplifier, Electrical Engineering

Assignment Help:

Q. Show the Frequency response of Rc Coupled Amplifier?

1. At low frequency i.e,less than 50 Hz reactance of Cc is going high hence same part of the signal will pass from one stage to next stage.CE cannot shunt RE because of its large reactance at low frequency.These factors cause falling of voltage gain.

2. At higher frequencies i.e, greater than 20 kHz reactance of Cc is very small and it behaves as a short circuit.This increase the loading effect of the next stage and reduces the voltage gain.At high frequencies, the capacitive reactance of base-emitter is very low which increases the base current.So b reduces and voltage gain drops off.

3. At mid frequency i.e, 50Hz to 20kHz ,the voltage gain is constant.Cc in this frequency range is such as to maintain a uniform voltage gain.Thus as frequency increases reactance of Cc decreases that tends to increase the gain.However lower reactance means higher loading of first stage and hence lower gain.So the two factors cancel each other resulting in a uniform gain at mid frequencies.


Related Discussions:- Show the frequency response of rc coupled amplifier

Find the rotor copper loss, A three-phase, 50-hp, 440-V, 60-Hz, four-pole, ...

A three-phase, 50-hp, 440-V, 60-Hz, four-pole, wound-rotor inductionmotor operates at a slip of 0.03 at full load,with its slip rings short-circuited. The motor is capable of devel

Determine the capacitor voltage, Q. In an RLC series circuit excited by a v...

Q. In an RLC series circuit excited by a voltage source v(t), for R = 10 , L = 1 H, and C = 0.1F, determine v(t) if the capacitor voltage vC(t) = 5e -10t V.

Opto couplers, Is there an opto-coupler that has a blocking voltage, VRRM, ...

Is there an opto-coupler that has a blocking voltage, VRRM, of greater than 800 volts? Perhaps, 1200 or 1600 volts? The manufacturer?

Electrical Machine, i have an assignment due for submission within two days...

i have an assignment due for submission within two days. It is all about transformer measurement manually and numerical results using Matlab.Is there anyone can do the job?

CRO, draw a labled diagram of CRO and explain the function of its parts

draw a labled diagram of CRO and explain the function of its parts

What do you understand by orthographic projection, What do you understand b...

What do you understand by orthographic projection ? Illustrate with the help of Matrix representation.

M6a2: lab: the floating-point unit, Introduction The purpose of this ex...

Introduction The purpose of this experiment is to examine the operation of the floating-point unit. Procedure 1. Show how the number 355.6 is converted into a normalize

For carry flag , For carry flag  CC ( Call on Carry ) and CNC ( Call ...

For carry flag  CC ( Call on Carry ) and CNC ( Call  on No Carry ) Instructions CC Calls  the subroutine form  the specified memory  location if carry flag  is set (CY=

Wire-line and fiber-optic channel, Q. Wire-line and Fiber-optic channel? ...

Q. Wire-line and Fiber-optic channel? Wire-line channels are used extensively by the telephone network for voice, data, and video transmission. Twisted-pair wire lines (with

In the circuit, see figure on this link: http://tinypic.com/r/1zodevk/8. ...

see figure on this link: http://tinypic.com/r/1zodevk/8. A. j400 I1-j1200 I2 (A) B. -j400 I1+j1600 I2 (A) C. j400 I1+j400 I2 (A) D. -j400 I1-j400 I2 (A)

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd