Show the coating application, Mechanical Engineering

Assignment Help:

Q. Show the Coating Application?

Immediately following surface preparation, the cleaned pipe shall be uniformly preheated by a non-contaminating method to the application temperature recommended by the manufacturer, but not to exceed 525°F (275°C). Any pipe exceeding 525°F (275°C? shall become the property of the Applicator, and Applicator shall reimburse the OWNER for its total value.

Pipe shall be coated as soon as possible, within a maximum of 4 h of surface preparation. Oxidation of the pipe surface prior to coating, in the form of "blueing" or other apparent formation is not acceptable. If such oxidation occurs, the pipe shall be cooled to the ambient temperature and recleaned at no expense to OWNER.

The powdered epoxy shall be applied to the pipe surface by the electrostatic spray method at a sufficient rate to provide a uniform cured film thickness. Unless otherwise directed by the purchase order the applied film shall be a nominal 20 mil (0.51 mm) average thickness with 18 mil (0.46 mm) minimum thickness and a maximum thickness of 24 mil (0.61 mm). Pipe so rejected by the Company shall be stripped and recoated at no extra cost to OWNER. The coating shall be applied over the full length of pipe to within a maximum of 6" (152 mm) and a minimum of 2" (51 mm) from the ends of the pipe.

In the event that the specified coating thickness is inadequate to obtain less than the maximum allowable holidays per joint of pipe, the Applicator and OWNER shall evaluate the cause for the excessive holidays and determine if the thickness as specified should be altered.


Related Discussions:- Show the coating application

Find the maximum torque - i-section, Find the maximum torque - I-section: ...

Find the maximum torque - I-section: An I-section 150 × 80 mm has flanges 6 mm thick and web 4 mm thick. Discover the maximum torque that may be safely applied if the shear st

Multiple spot welding, Multiple Spot Welding This is a modification of sp...

Multiple Spot Welding This is a modification of spot welding, in which two or more than two welds can be obtained simultaneously from each transformer secondary. For specific pro

Refractoriness, Refractoriness The capability of a material to withstan...

Refractoriness The capability of a material to withstand the action of heat devoid of appreciable deformation of softening is submitted to as refractoriness. Such property is m

Angle of twist is zero on the shaft, Angle of twist is zero on the shaft: ...

Angle of twist is zero on the shaft: A shaft 10 m long and 100 mm diameter during its length is fixed at the ends and is subjected to two opposite torques of 8 kN-m and 10 kN-

What do you mean by thermodynamic equilibrium, What do you mean by thermody...

What do you mean by thermodynamic equilibrium? Compare irreversible process with reversible process. Give some examples of irreversible process.

What is the basic working principle of capacitive transducer, Answer any fi...

Answer any five questions. a) Describe calibration and state its types. b) Which are the kinds of test signals? c) What is the basic working principle of piezo-electric tr

Communication protocols applicable in holonic manufacturing , Communication...

Communication Protocols Applicable in Holonic Manufacturing System Communication amongst agents plays an essential role in the Holonic manufacturing system. Exchange of informa

Find out maximum bending stress induced in beam, Q. A beam made of C.I. hav...

Q. A beam made of C.I. having section of 50mm external diameter and 25 mm internal diameter is supported at 2 points 4 m apart. The beam carries concentrated load of 100N at the ce

Shear force and bending moment diagrams and contra flexure, Draw the shear ...

Draw the shear force and bending moment diagrams for the beams shown in Figures 4 and 5. Also find the maximum shear force, bending moment and the points of contra-flexure

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd