Show steady-state sinusoidal analysis with pspice, Electrical Engineering

Assignment Help:

Q. Show Steady-State Sinusoidal Analysis with PSpice

PSpice can easily solve steady-state ac circuits for currents and voltages. Ac voltage sources, which must begin with the letter V, are specified by statements of the form

VNAME N+ N- AC VPEAK PHASE

whereVNAME is the name of the voltage source,N+is the node number of the positive reference, N- is the node number of the negative reference, AC indicates that this is an ac source, VPEAK is the peak value of the voltage, and PHASE is the phase angle of the source in degrees. Current sources, which must begin with the letter I, are specified in a similar manner, with the reference direction for the current source pointing from the first node number given in the statement to the second node number.

The ac analysis request is made with a statement of the form

• AC LIN NPOINTS STARTFREQ STOPFREQ

where • AC designates a request for frequency analysis, LIN defines a linear frequency sweep with NPOINTS specifying the number of points in the sweep starting at the STARTFREQ and finishing at the STOPFREQ. For example, to carry out a steady-state ac analysis for a frequency of 60 Hz, the analysis request would be

• ACLIN16060


Related Discussions:- Show steady-state sinusoidal analysis with pspice

Construction and operation of enhancement mosfet, Q. Explain the constructi...

Q. Explain the construction and operation of Enhancement MOSFET? The construction of an N-channel enhancement MOSFET is shown in figure below. Two highly doped N + regions are

Mini computers - introduction to microprocessors , Mini Computers Large...

Mini Computers Larger  computer  more  computing  power  having  capability to address  more  memory  and  more  speed  than  microcomputer called minicomputer. These computers

Calculate the gross torque developed for a flux, Q. A four-pole, dc seriesm...

Q. A four-pole, dc seriesmotor has a lap-connected, two-layer armature winding with a total of 400 conductors. Calculate the gross torque developed for a flux per pole of 0.02 Wb a

Common-drain jfet amplifier, Q. Common-Drain JFET Amplifier? Figure (a)...

Q. Common-Drain JFET Amplifier? Figure (a) shows a CD JFET amplifier in which resistors R 1 , R 2 , and R SS are selected by the bias design, and capacitors CG and CS are chos

Ideal operational amplifier, list the key parameters to describe the ideal ...

list the key parameters to describe the ideal operational amplifier

Electronic instrumentation and measurements, why is a delay line used in th...

why is a delay line used in the vertical selection of oscilloscope?

Illustrate the photo-conductive cell, Illustrate in detail digital encoders...

Illustrate in detail digital encoders. Illustrate the following with their application: Photo-conductive cell Photo-voltaic cell

Explain bound instructions in 8086 family, Explain BOUND instructions in ...

Explain BOUND instructions in 8086 family with example and their effect on flag. BOUND: The BOUND instruction, that has two operands, compares a register along with two word

Calculate the sending end voltage, A 150 km long, 3-phase, 400 kV overhead ...

A 150 km long, 3-phase, 400 kV overhead line is used to transmit 1800 MW to a distribution area at 0.9 power factor lagging. The line parameters per phase and per unit length in st

Illustrate signal attenuation, Q. Illustrate Signal attenuation? Signal...

Q. Illustrate Signal attenuation? Signal attenuation in many channels can be offset by using amplifiers to boost the signal level during transmission. However, the amplifier al

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd