Op-amp amplifier, Electrical Engineering

Assignment Help:

A voltage signal generated by a sensor conditioning circuit varies from -0.5V to +0.5V . The signal from the sensor is to be connected to the analog to digital  converter which only accepts positive voltage. Design an op-amp circuit to amplify the signal 10 times and shift the signal to the positive range.  The output signal after amplification and shifting should fluctuate between 0 V to 10 V.  Simulate your design using Multisim spice simulator and show that your design meets all the requirements. Take note that the final output signal should not be inverted. Your type written answer should contain

i)  Circuit schematics that show the complete circuit and its resistor value.

ii) Plot showing input and output voltage of your circuit. Assume sinusoidal input signal with peak to peak voltage of 1 V.

iii) Explain how the circuit works and show all calculation steps.

iv) List all components used together with its product code and price. Information on practical components should be obtained from Analog Devices, Farnell or RS website.


Related Discussions:- Op-amp amplifier

Depletion zone in p-n junction, Depletion Zone in P-N Junction The pow...

Depletion Zone in P-N Junction The power of the depletion zone electric field gets increases as the reverse-bias voltage increases. One time the electric field intensity incre

Schottky diodes - types of power diodes , Schottky  diodes The schot...

Schottky  diodes The schottky diodes have very fast recovery time and  low forward drop.  The current  ratings of  these diodes  vary  from 1A to 300 a and  maximum  allowable

Wye-delta transformation., what is the literature review about wye delta tr...

what is the literature review about wye delta transformation?? for 3 paragraphs atleast*

Define the half duplex with respect to serial communication, With respect t...

With respect to serial communication define the half duplex. Half Duplex Transmission: A channel of half duplex can send and receive, but not at same time. It's like a one-la

Compute the voltage, Q A point charge Q 1 =-5 nC is located at (6, 0, 0). ...

Q A point charge Q 1 =-5 nC is located at (6, 0, 0). Compute the voltage v ba between two points a(1, 0, 0) and b(5, 0, 0). Comment on whether point a is at a higher potential wi

Illustrate working of direct-coupled amplifiers, Q. Illustrate working of D...

Q. Illustrate working of Direct-coupled Amplifiers? Direct-coupled Amplifiers : The following figure shows a direct-coupled amplifier consisting of two stages. A dc voltage i

What do you mean by antenna gain, Q. What do you mean by Antenna gain? ...

Q. What do you mean by Antenna gain? Antenna gain depends on both shape and size. Dipole antennas, commonly used at lower radio frequencies, are made up of a rod or wire of len

Use of n-channel jfet, Q. Use of N-channel JFET? Generally, N-channel J...

Q. Use of N-channel JFET? Generally, N-channel JFETs are more commonly used than P-channel. With no voltage applied between gate and source, the channel is a wide-open path for

Determine the slip at which maximum torque, A three-phase, 220-V, 60-Hz, fo...

A three-phase, 220-V, 60-Hz, four-pole, wye connected induction motor has a per-phase stator resistance of 0.5 . The following no-load and blocked rotor test data on the motor are

Explain thevenin''s theorem procedure, Thevenin's theorem procedure:   1. ...

Thevenin's theorem procedure:   1.  Open circuit R L and find Thevenin's voltage (V TH ). 2.  Find Thevenin's resistance (R TH ) when voltage source is short circuit or curren

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd