MATLAB support for fault analysis in transmission lines, Electrical Engineering

Assignment Help:
The devices in power system shown in Figure 2 have the following ratings:

G1 : 100 MVA, 13.8 kV grounded Y, X” = 0.15 pu, X2 = 0.015 pu Xo = 0.05 pu
G2 : 50 MVA, 20.0 kV grounded Y, X” = 0.15 pu, X2 = 0.015 pu Xo = 0.05 pu
T1 : 100 MVA, 13.8/138 kV (both grounded), X1 = 0.08 pu, X2 = 0.08 pu Xo = 0.08 pu
T2 : 50 MVA, 20.0/138 kV, ?-Y grounded Y, X1 = 0.08 pu, X2 = 0.08 pu Xo = 0.08 pu
L1 : 100 MVA, 138 kV grounded X1 = 19 ?, X2 = 19 ?, Xo = 50 ?,


Figure 2

Assume that all resistances in the power system can be neglected. The system base apparent power is ____ (to be specified by your lecturer)MVA, and the base line voltage is 13.8 kV at bus 1. Assume that the voltage at bus 1 is 13.8 kV and that the power system is initially unloaded.

2. Use Matlab to:

a. Find the sub transient per-phase equivalent circuits of this power system for positive-, negative- and zero-sequence component.

b. Find the subtransient fault current at the fault found at the location indicated by X for:



i) A symmetrical three-phase fault
ii) A single line-to-ground fault
iii) A line-to-line fault
iv) A double line-to-ground fault

(A student will solving for the transient fault line current for two (2) types of fault to be specified by the lecturer).

Related Discussions:- MATLAB support for fault analysis in transmission lines

Find the parameter values for channel mosfet, Q. Find the parameter values ...

Q. Find the parameter values V T and I DSS for a p- channel MOSFET with i D = 0 when v GS ≤-3 V, and i D = 5 mA when v GS = v DS =-8V.You may neglect the effect of v DS on

Dsp., fir and iir filter design

fir and iir filter design

Sod output - serial input output ports , SOD Output Serial output data ...

SOD Output Serial output data  single  bit can be sent  out through this pin using SIM  command  discussed in details in chapter8.

Mov - move instruction, MOV ( Move ) Instruction It copies  the content...

MOV ( Move ) Instruction It copies  the contents of the sources register into destination register. The general format is . This  instruction  is used  to copy 8 bit  from s

Can you explain about multiple poles, Q. Can you explain about Multiple Pol...

Q. Can you explain about Multiple Poles? Let us consider that F 1 (s) has all simple poles except, say, at s = p 1 which has a multiplicity m. Then one can write When

Explain information obtained for the load flow analysis, Explain Informatio...

Explain Information Obtained for the Load Flow Analysis (i)  Magnitude and phase angle of the voltage at each bus. (ii)  Active and Reactive power flow in each line. (iii

Show voltage wave form of rlc series circuit, Q. The voltage wave form of F...

Q. The voltage wave form of Figure is applied to an RLC series circuit with R = 2, L = 2H, and C = 1 F. Obtain i(t) in the series circuit. (Note that the capacitor and inductor va

Storage oscilloscope, Aim To build a simple storage oscilloscope usi...

Aim To build a simple storage oscilloscope using the PIC trainer To report on the program's design and operation Equipment PIC Trainer and PICkit3 in-circui

Explain the delay model, Explain the delay model based on logical effort of...

Explain the delay model based on logical effort often used in estimating delays in logic cells. Hence use the model to predict the delay of a 4-input NOR logic cell with a 3 times

Explain the working of a darlington pair, Q. Explain the working of a darli...

Q. Explain the working of a darlington pair? This is two transistors connected together so that the current amplified by the first is amplified further by the second transistor

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd