Load flow studies from power generation and distribu, engineering, Other Engineering

Load flow studies from power generation and distribu, engineering, Other Engineering

Assignment Help:

The load data given in Table 1 belongs to a power company. Develop the daily load curve for the primary feeder. Also, determine:
a. maximum coincident demand of the system
b. demand factor if the feeders total connected load is 4MW
c. utilisation factor, if the feeders rated capacity is 5MW
d. load factor
e. diversity factor
f. coincidence factor
g. load diversity
h. loss factor
Table 1: Daily load curve data for question 1
Time Load(kW)
Residential Commercial Lights
00:00 250 300 100
01:00 250 300 100
02:00 250 300 100
03:00 250 300 100
04:00 250 300 100
05:00 250 300 100
06:00 250 300 100
07:00 350 300
08:00 450 400
09:00 550 600
10:00 550 1100
11:00 550 1100
12:00 600 1100
13:00 600 1100
14:00 600 1300
15:00 600 1300
16:00 600 1300
17:00 650 1300
18:00 750 900
19:00 900 500
20:00 1100 500 100
21:00 1100 500 100
22:00 900 300 100
23:00 700 300 100
24:00 250 300 100

Related Discussions:- Load flow studies from power generation and distribu, engineering

Mechanical engineering, What is the specific heat of water at different pre...

What is the specific heat of water at different pressure and different temperature? Is it possible to boil the water below atmospheric pressure and use as a hot bathing water?

Civil engineering, how to prepare assignment note on culverts in between 4 ...

how to prepare assignment note on culverts in between 4 to 6 pages

Cash Conversion Cycle, The need for working capital to run the day-to-day b...

The need for working capital to run the day-to-day business activities cannot be overemphasized. We will hardly find a business firm which does not require any amount of working ca

Mass Balances, Engineers sometimes add chlorine to pipes to disinfect water...

Engineers sometimes add chlorine to pipes to disinfect water. It is desired to achieve four logs of kill. This means that the effluent concentration of microoganisms is 10^-4 times

Blow hole and pin hole porosity, Blow Holes (i) Exc...

Blow Holes (i) Excessive moisture in the moulding sand. (ii) Low permeability and excessive fine grain sands. (iii

Compacting or briquetting, The operation of heating a green compact to an e...

The operation of heating a green compact to an elevated temperature is known as sintering. It is a process by which solid bodies are bonded by atomic forces. It is carried out belo

Difference amplifier, Difference amplifier: Figure shows how two inputs...

Difference amplifier: Figure shows how two inputs can be subtracted. This circuit differs from previous types with negative feedback in that the non-inverting terminal is not

New building completion - fire safety management, Ne w building completion...

Ne w building completion: New buildings have to be constructed to meet certain fire safety standards. It is not acceptable for buildings to be built that do not attain a min

Introduction to Corporate Finance, Calculatethe tax disadvantage to organiz...

Calculatethe tax disadvantage to organizing a U.S. business today, after passage of the Jobs and growth Tax relief reconciliation act of 2003, as a corporation versus a partnership

Financial engeneering, “A swap bank has to entail certain risks which are i...

“A swap bank has to entail certain risks which are inherent to the swap business and are interrelated” Explain the risks involves in swap business.

Write Your Message!

Name

Email id

Message

Verfication Code

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd