Determine line voltage for the y- connected machine, Electrical Engineering

Assignment Help:

A 3-phase, 16-pole synchronous machine is driven by a prime mover at a speed of 600-rpm with the stator open circuited. The rotor flux per pole is 0.025-Wb. Determine

(a) the frequency and rms value of the induced voltage in the stator per phase having 450 effective turns;

(b) line voltage for the Y-connected machine.

 Solution:  

(a)    The frequency of the stator voltage is from (1.1): f = pn/60 = 8.600/60 = 80-Hz.

The voltage generated per phase is using (1.4): 

Eφ = 4.44 .80.450.0.025 = 3996 - V ≈ 4 - kV.

(b)   The voltage across the stator terminals (line-to-line) is VLL = √3. 3996 = 6921.3 -V.


Related Discussions:- Determine line voltage for the y- connected machine

Equivalent series impedance referred to the high-voltage, Q. A 25-kVA, 2300...

Q. A 25-kVA, 2300:230-V, 60-Hz, single-phase transformer has the following parameters: resistance of high-voltage winding 1.5 , resistance of low-voltage winding 0.015 , leakage

What is meant by microcontroller, What is meant by microcontroller? A d...

What is meant by microcontroller? A device which having the microprocessor with integrated peripherals like memory, serial ports, parallel ports, timer/counter, interrupt contr

Which Transistor configuration best to use in cascade, Q. Which of the 3 tr...

Q. Which of the 3 transistor configuration is best to use in cascade if maximum voltage gain is to be realized?  The common collector configuration is not used for intermediate

Analog signal processing, Derive Equation 13-20 pertaining to the convers...

Derive Equation 13-20 pertaining to the conversion algorithm based on redefined unit capacitor

Analog circuit analysis, consider a single stage ce amplifier with rs=1kohm...

consider a single stage ce amplifier with rs=1kohm,r1=50ohm,r2=2kohm,rc=1kohm,rl=1.2kohm,hfe=50,hie=1.1kohm,hoe=25microamp/volt and hre=2.5*10-4

The octal inverter 74ls 240, The  Octal Inverter 74LS 240 It is  simil...

The  Octal Inverter 74LS 240 It is  similar  to above  octal  buffer  but with  inverter output. The  logic  diagram is  shown  in figure below . Normal 0

Clipper, merits amd demerits of series and shunt clipper

merits amd demerits of series and shunt clipper

Can you explain about trapeziodal clippers, Q. Can you explain about Trapez...

Q. Can you explain about Trapeziodal Clippers? During The Positive half cycle, the diode D1 will be open circuited and the input appears as the output until, the applied bias v

What is the need of the resistance used in a clipper, Q. What is the need o...

Q. What is the need of the resistance used in a clipper? Resistor is used in a clipper to limit the current through the diode. To avoid the damage due to excessive current thro

Working principle of ultrasonic machining, Explain the basic working princi...

Explain the basic working principle of ultrasonic machining with the help of diagram. What are the different kinds of tool materials explain, tool holders are used in ultrasonic

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd