Causes and remedies of motorcycle problems , Mechanical Engineering

Assignment Help:

CAUSES AND REMEDIES OF MOTORCYCLE PROBLEMS

 If Engine Overheats Causes of Problem

Remedy

 

  • Incorrect spark plug make/model used
  • Longer reach spark plug used
  • Gasket missing
  • Plug tightened insufficiently
  • Worn out/aged spark plug
  • Timing too much advance
  • Low octane petrol used
  • Air-fuel mixture too lean
  • Lubrication system faulty
  • Excessive carbon deposits
  • Valves/Valve springs defective
  • Compression ratio high
  • Cylinder head gasket projecting into combustion chamber
  • Excessive load due to binding brake
  • Tyre under-inflated
  • Slipping clutch
  • Operation at high altitudes
  • Overloading

 

 

  • Use correct type
  • Use correct reach plug
  • Replace
  • Retighten
  • Replace
  • Adjust
  • Use good fuel
  • Adjust carburetor
  • Check and rectify cylinder head
  • Decarbonise cylinder head
  • Rectify/replace
  • Correct
  • Replace gasket
  • Adjust brakes
  • Inflate to correct pressure
  • Adjust/replace clutch plates
  • Avoid
  • Avoid

 


Related Discussions:- Causes and remedies of motorcycle problems

What do you mean by vibration, (a) What do you mean by vibration and the te...

(a) What do you mean by vibration and the terminology used in it to be defined? (b) A body is subjected to two Harmonic motions as provided below x 1 = 10 sin (wt + π/6) and x

Explain working of plate heat exchangers, Q. Explain working of plate heat ...

Q. Explain working of plate heat exchangers? For gasket plate heat exchangers handling flammable materials, the same spacing requirements for air coolers should be applied. If

Velocity - area method, Q. What do you mean by Velocity - Area Method? ...

Q. What do you mean by Velocity - Area Method? Out of the above four categories, velocity area method is most widely used and provides more accurate results. Requirements of a

Theory machines, Explain lower pair. and kinematics chair

Explain lower pair. and kinematics chair

Determine the reactions at beam, Determine the reactions at bea: A can...

Determine the reactions at bea: A cantilever AB, 1.8 m long is fixed at A and carries uniformly distributed load of 20 kN/m over its entire length and a point load of 30 kN at

Make evaluation for the engine efficiency, (a) Differentiate between carnot...

(a) Differentiate between carnot Heat pump and carnot Heat engine. What is the basic cycle for a carnot Heat pump ? Explain it. (b) A reversible heat engine delivers 0.6 K at po

Explain how the rankine cycle efficiency is improved, Illustrate how the Ra...

Illustrate how the Rankine cycle efficiency is improved by the following : a. Lowering the condenser pressure. b. Increasing the pressure of steam. c. Superheating the ste

Show the support locations for truckable skid, Q. Show the support location...

Q. Show the support locations for truckable skid? Unless instructed otherwise by Engineer, support locations for truckable skid shall be determined by skid Vendor. Support loca

Friction, FRICTION: you have learnt laws of friction and problems invo...

FRICTION: you have learnt laws of friction and problems involving dry friction. The relative sliding motion of one body on another body is resisted by forces called as frictio

Find the cycle efficiency, Develop an EES Code for a Rankine cycle with reh...

Develop an EES Code for a Rankine cycle with reheat and with 2 open feedwater heaters.  The cycle is shown below:  Use the following conditions: 1.  700 psi, 850F 2.  500

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd