Your family grows over time and the required water supply

Assignment Help Mechanical Engineering
Reference no: EM13631096

Suppose you build a rural house, where you need to run a pipe to the nearest water supply, which fortunately is about 1 Km above the elevation of your house. The gage pressure at water supply is 1 Mpa and the pipe length will be about6 Km. You require a minimum of 3 gal/min when you your end of the pipe is open to the atmosphere. To minimize cost, you want to buy the smallest possible diameter pipe.

(a) plot the pressure loss from pipe inlet to exit, neglecting minor losses, as a function of roughness for various pipe materials.

(b) which is more important to this problem, the loss due to elevation difference, or the loss due to the pressure drop in the pipe?

(c) your family grows over time and the required water supply grows beyond the 3gal/min Plot the required pipe diameter as a function of water supply requirement, now assume that the pipe is a very smooth one.

Reference no: EM13631096

Questions Cloud

A completely reversible refrigeration cycle removes heat at : a completely reversible refrigeration cycle removes heat at a rate of 100kw from an industrial refrigerator maintained
During the process the pressure and specific volume are : water vapor in a piston-cylinder assembly undergoes a process from saturated vapor at 150 c to a pressure of 300 kpa.
A 45 wt pb-55 mg alloy is rapidly quenched to room : a 45 wt pb-55 mg alloy is rapidly quenched to room temperature from an elevated temperature in such a way that the high
An isentropic steam turbine processes 5kgs of steam at 4mpa : an isentropic steam turbine processes 5kgs of steam at 4mpa. the majority of this steam is exhausted at 50kpa and 100
Your family grows over time and the required water supply : suppose you build a rural house where you need to run a pipe to the nearest water supply which fortunately is about 1
If the maximum temperature of the cycle is 2200k determine : consider an air standard otto cycle with a compression ratio of 8. the engine inlet conditions are p100 kpa t290k and
At location one fluid with a density of 121times103 kgm3 is : the equation of continuity states the mass flow rate has the same value at every position along a tube that has a
A car with a mass of 1570 kg is supported by four springs : a car with a mass of 1570 kg is supported by four springs each with a spring constant of 25 nmm. in traveling over an
A metal block of mass 1220 kg is hanging from a string the : a metal block of mass 1.220 kg is hanging from a string. the tension in the string is 7.712 n. the block is submerged

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd