You must put this on a 101 cm diameter axel what

Assignment Help Mechanical Engineering
Reference no: EM13645583

One way to put a steel wheel on a steel axel (for example on a railroad car) is to heat the wheel until it slides on the axel, then cool. Assume you have a 1 meter diameter steel wheel with a 10 cm diameter circular hole in the middle at room temperature (25 degrees C). You must put this on a 10.1 cm diameter axel. What temperature must the wheel be heated to? The linear thermal expansion coefficient for steel is 12*10^-6 degrees C^-1.

Reference no: EM13645583

Questions Cloud

Five samples of the material were tested in a structure : five samples of the material were tested in a structure and the average interior temperature reported was as follows
Horizontal conductor a horizontal conductor that is part of : 1 potential difference an electron is accelerated through a potential difference of 2.2 kv and directed into a region
Determine a the finite difference equations and b the nodal : consider steady two-dimensional heat transfer in a rectangular cross section 60 cm x 30 cm with the prescribed
A what is the smallest angle between the magnetic field and : a coil carries a current and experiences a torque due to a magnetic field. the value of the torque is 80 of the maximum
You must put this on a 101 cm diameter axel what : one way to put a steel wheel on a steel axel for example on a railroad car is to heat the wheel until it slides on the
When a different particle with an electric charge of 400 : a velocity selector has an electric field of magnitude 2470 nc directed vertically upward and a horizontal magnetic
A 55 horsepower 1800 rpm electric motor is connected to a : a 55 horsepower 1800 rpm electric motor is connected to a speed reducer with a ratio of 171. neglecting friction in the
A 97 confidence interval in inches for the mean height of a : a 97 confidence interval in inches for the mean height of a population is 65.4 67.0. this result is based on a sample
What is the minimum coefficient of friction necessary : you have been asked to design a four-wheel drive vehicle capable of ascending a 24 degree ramp. what is the minimum

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  During a harsh winter the ground surface is frozen to a

the pipe that supplies drinking water to a community in a cold region of the planet is buried a depth of 3m from the

  With corresponding surface temperatures of t1 30 degc and

a pipe is made of a material the thermal conductivity of which is simultaneously dependent on radius and temperature

  A 1000-meter-long pipe closed at one end was inverted and

a 10.00-meter-long pipe closed at one end was inverted and submerged vertically in a minnesota lake until the closed

  If a system has two redundant safety systems with failure

if a system has two redundant safety systems with failure rates of 0.16 and 0.22 faults per year respectively what is

  Does the second law require that the decrease in entropy of

consider two solid blocks one hot and the other cold brought into contact in an adiabatic container. after awhile

  Determine the maximum speed

Determine the maximum speed at which the car with mass m can pass over the top point A of the vertical curved road and still maintain contact with the road.

  What is the ratio of the dynamic viscosity of air to that

what is the ratio of the dynamic viscosity of air to that of water at standard pressure and temperature of 20degc? what

  Find the cartesian components of force p acting in the x y

find the cartesian components of force p acting in the x y and z directions given p20n alpha 134.5 deg beta 55.0 deg

  Determine a the largest value less than 45deg of the angle

the initial velocity v0 of a hockey puck is 105 mih. determine a the largest value less than 45deg of the angle a for

  Find the speed which makes the cost of a voyage of 2000 sea

the cost per hour of running a ship at a speed of v knots is pound 4 v3 2048. find the speed which makes the cost of

  An axial flow compressor stage has blade rootmean and tip

an axial flow compressor stage has blade rootmean and tip velocities of 150200 and 250 ms. the stage is to be designed

  Two kg of a mixture having an analyis of on a mass basis of

two kg of a mixture having an analyis of on a mass basis of 30 nitrogen 40 carbon dioxide 30 oxygen is compressed

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd