You achieve this final condition by a series of steps

Assignment Help Mechanical Engineering
Reference no: EM13631102

Suppose you need a wire with a tensile strength of 80 ksi and a diameter of 0.19 inches. Your starting material is a 1 inch diameter rod. You achieve this final condition by a series of steps, drawing the rod into finer and finer dimensions and then annealing. For the final step, what should be the starting diameter of the wire?

Reference no: EM13631102

Questions Cloud

Water is the working fluid in an ideal rankine cycle : water is the working fluid in an ideal rankine cycle. saturated vapor enters the turbine at 18 mpa. the condenser
Should electric power plants reject energy by heat transfer : should electric power plants reject energy by heat transfer to large blocks of ice that are maintained by a
Now consider a nucleus of charge ze with two electrons use : a. aingly-ionized lithium has a nucleus of charge 3e and two electrons. use the variational principle to estimate the
Identify the approximate values of each of the parameters : identify the approximate values of each of the parameters listed below based on the graph.a yield strengthb tensile
You achieve this final condition by a series of steps : suppose you need a wire with a tensile strength of 80 ksi and a diameter of 0.19 inches. your starting material is a 1
Archaeologists often find only parts of ancient human : archaeologists often find only parts of ancient human remains. for example they may find a small finger bone called the
A completely reversible refrigeration cycle removes heat at : a completely reversible refrigeration cycle removes heat at a rate of 100kw from an industrial refrigerator maintained
During the process the pressure and specific volume are : water vapor in a piston-cylinder assembly undergoes a process from saturated vapor at 150 c to a pressure of 300 kpa.
A 45 wt pb-55 mg alloy is rapidly quenched to room : a 45 wt pb-55 mg alloy is rapidly quenched to room temperature from an elevated temperature in such a way that the high

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What would be the final temperature of 1 m3 of atmosphere

the atmosphere on maris is comprised of mostly carbon dioxide at a pressure of 600 pa that is not a mistake it is in

  Using a unifrom mesh size deltax deltay determine the

consider steady two dimensional heat transfer in a square cross section 3cm x 3cm with the prescribed temperatures at

  Determine the maximum sustainable torque that the solid

a solid circular shaft and a tubular shaft both with the same outer radius of cco 0.600in are being considered for a

  Determine fourier number compare two identical steel spheres

Determine Fourier Number, Compare two identical steel spheres, except the first has a two inch diameter while the second sphere has a four inch diameter. The larger sphere will have a Fourier number approximately

  Determine the heat transfer that occurred during this

the saturated water vapor contained in a closed rigid tank has a mass of 2000 kg. the water vapor is cooled down from

  What are the forces on the pinion gear and shafts

What are the forces on the pinion,gear,and shafts?

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Obtain a relation for the variation of pressure in the

temperature varies with altitude. the variation in the temperature can be approximated by tt0 -beta z where t0 is the

  If the velocity out the 2-cm-diameter tube is 15 ms

water flows into a volume that contains a sponge with a flow rate of 0.02 m3s. it exits the volume through two tubes

  Determine a t2 in 0r and b the rate of exergy destruction

air at t11300 0r p116 lbfin2 enters a counterflow heat exchanger operating at steady state and exits at p214.7 lbfin2.

  At 45 degrees celsius latitude the gravitational

at 45 degrees celsius latitude the gravitational acceleration as a function of elevation z above seas level is given by

  A piston mp 5 kg is fitted in a cylinder a 15 cm2 that

a piston mp 5 kg is fitted in a cylinder a 15 cm2 that contains a gas. the setup is in a centrifuge that creates an

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd