Wrtie the balance equations for each fluid stream in a

Assignment Help Mechanical Engineering
Reference no: EM13624437

A heat exchanger is a device in which heat flows between two fluid streams brought into thermal contact through a barrier, such as a pipe wall. Heat exchangers can be operated in either the cocurrent (both fluid streams flowing in the same direction) or countercurrent (streams flowing in opposite direction).

The heat flow rate from fluid 1 to fluid 2 per unit length of the heat exchanger, Q is proportional to the temperature difference (T1-T2): Q=(Heat flow rate from fluid 2 per unit length of heat exchanger) = k(T1-T2)

where k is a constant of proportionality with units of J/(m s K0. The fluids in the two streams are the same and their flow rates are equal. The initial and final temperatures of stream 1 will be 35C and 15C, respectively, and those for stream 2 will be -15C and 5 C.

a) Wrtie the balance equations for each fluid stream in a portion of the heat exchanger of length dL and obtain differential equations by letting dL->0.

b) Intergreate the energy balance equations over the length of the exchanger to obtain expressions for the temperature of each stream at any point in the exchanger for each flow confuguration. Also compute the length of the exchanger, in units of L0 = M Cp / 2k (where M is the mass flow rate of either stream), needed to accomplish the desired heat transfer.

c) Write an expression for the change of entropy of stream 1 with distance for any point in the exchanger.

Reference no: EM13624437

Questions Cloud

An angled jet of water comes from the ground at 5 m s at a : an angled jet of water comes from the ground at 5 m s at a 35 degree angle from the horizontal. how high does the
The diameters of bolts produced by a certain machine are : the diameters of bolts produced by a certain machine are normally distributed with a mean of 0.30 inches and a standard
Three seconds after a polisher is started from rest small : three seconds after a polisher is started from rest small tufts of fleece from along the circumference of the
A mass m1 31 kg rests on a frictionless table and : a mass m1 3.1 kg rests on a frictionless table and connected by a massless string over a massless pulley to another
Wrtie the balance equations for each fluid stream in a : a heat exchanger is a device in which heat flows between two fluid streams brought into thermal contact through a
The homogeneous gate shown in fig p288 consists of one : the homogeneous gate shown in fig. p2.88 consists of one quarter of a circular cylinder and is used to maintain a water
A researcher collects data on two independent samples the : a researcher collects data on two independent samples. the first group consists of 20 human subjects has a sample mean
There is a heat-pump that takes water from one side of the : a 630000 gallon tank sits empty outside where the temperature is 20 degrees f. the tank is then immediately filled
Two carts a and b are moving in a straight line with : two carts a and b are moving in a straight line with velocities v and 2v respectively. the length of each of the carts

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd