Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
a sequential circuit has one input (X) and one output (F). The circuit examines groups of four consecutive inputs and produces an output F=1 if the input sequence 0101 or 1001 occurs. The circuit resets after every four inputs. Write VHDL code for the circuit.
Find the Laplace transform of the following: (i) f(t)= 45e^(-5(t-6)) (j) f(t)=2 sin(t-6) (k) f(t)="4.8" e^(-5t) cos?(400t -36o) (l) f(t)=8 d2x/dt2 + 5 dx/dt where (dx(0))/dt = 8 and x(0) = -4
A Vs equals 1V source impedance 25ohms is connected by a switch to a 50-ohms lossless air transmission line 1 m long, terminated in a load of 30-ohms. At time t=0s, the switch is closed instantaneously to launch a step voltage down the line.
Given the following function: F(W,X,Y,Z) = fm(2,3,5,7,12,13). a. Implement the function using an 8-input multiplexer. b. Implement the function using a 4-input multiplexer.
The conveyor belt moves relatively slow therefore several seconds pass before the separator switches position. The piston moves two switches (N/A) when it is on position one or on position two. The control system requires a variable exit voltage b..
Two rectangular waveguides, one air filled with internal dimensions 2cm x 1cm and the other dielectric filled with internal dimensions 1cm x 0.5cm, have the same cut-off frequency for the dominant mode. what is The relative permittivity of the die..
A photoelectric surface has a work function of 4eV. What is the maximum velocity of the photoelectrons emitted by light if frequency 10^15 Hz incident on the surface h = 6.6 * 10^-34 Joules-second e = 1.6 * 10^-19 Coulomb
Design a synchronous sequential circuit that has a single input X and an output Y. Y goes to 1 if x(t) = x(t - 2). At all other times Y is to be 0. Use Moore model and JK flip-flop to implement the circuit. (a) Make the state definition
two resistors with nominal values of 4.7K ohm and 10K ohm, are used in a voltage divider with a +15V supply to create a nominal +10V output. Assuming the resistor values to be exact, what is the actual output voltage produced
a single phase 10kVA, 2400/120 V transformer has the following equivalent measurements (referenced to high side): Rc 64k ohms, Xm 9.6k ohms, Re 19.3 ohms, Xe 73.3 ohms. if the secondary load is Zl = 5 angle 30 degrees ohms
The respective resistance measurements (from the first bar) are 11.1 kW, 12.1 kW, and 14.5 kW.Find the a) material resistivity and b) contact resistivity, then c) restate the material resistivity as a sheet resistivity.
The voltage on a 40 µF capacitor is found to be 12(1 - e-8t) volts. Find the voltage at t = 0, and the voltage at t = 0.1 second. How much energy is stored on the capacitor as t approaches infinity
If the breakdown voltage increases with temperature at a rate of 40 mV/"C, find the break-down voltage of the diode at room temperature, assuming that the space-charge resistance is 10 C& independent of temperature.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd