Write report on high voltage power transmission line design

Assignment Help Electrical Engineering
Reference no: EM131039091

1. Introduction

This section should reflect your literature survey of the subject of high voltage power transmission line design and operation. (1-page, single-space)

2. Power Transmission Line Design-Problem Statement

This section should present the design problem with all the specs and requirements (1/2-page, single spaced)

3. Transmission Line Design Procedures

This section should present the design procedures as well as the most important equations, relationships, tables, models, as well as assumptions made. Also TL. characteristics such as and Transmission efficiency must be derived if necessary. (2-pages, single-spaced)

4. Transmission Line Design Results and Discussion
This section must show all design parameters and characteristics output of your design as %veil as a short discussion of the results (2-pages, single-spaced)

5. High Voltage Transmission Line Electric and Magnetic Field profiles

Establish the need to calculate the electric and magnetic field profiles underneath electric power transmission lines

6. The Impacts of Power Transmission Lines ( I -to-2 pages, single spaced)

6-a: Contemporary issues related to high voltage power transmission lines
6-b: Impact of HV power transmission lines on society
6-c: The ethics and professionalism in design, installation, and operation of transmission lines
6-d: The need for Continuous learning in the field of HV Power Transmission lines

7. Conclusions (1/2-page, single spaced)

8. References

Document all references used. No www references. At least two IEEE papers along with professional handbooks.

Reference no: EM131039091

Questions Cloud

Create two more unit plans integrating science : Just create two more unit plans integrating science and math content of fractions, decimals, and/or percents. Ensure you have listed each of the science (NSES)) and math (NCTM) standards to include learning goals and objectives.It should be a sing..
What will be dollar cost of hedging with forward contract : How would you hedge your exposure with forward contracts and option contracts and what will be the dollar cost of hedging with forward contract?
Create a gantt chart illustrating the project tasks : Be typed, double-spaced, using Times New Roman font (size 12), with one-inch margins on all sides; citations and references must follow APA or school-specific format. Check with your professor for any additional instructions.
What is the mean of your sample : Obtain, generate, or select your own random set of 120 integers between 1 and 100. You may use a calculator, excel, or a table of random numbers to achieve this. Use your sample to answer the following questions:
Write report on high voltage power transmission line design : Write a good engineering report on high voltage power transmission line design and operation. Establish the need to calculate the electric and magnetic field profiles underneath electric power transmission lines.
Compare the role and powers of the office of management : Compare the role and powers of the Office of Management and Budget to the Congressional Budget Office. Choose a current policy issue. Discuss this issue in terms of the stages of the policymaking process.
Testing a random sample of eight of them : A computer company will screen a shipment of 30 processors by testing a random sample of eight of them. How many different samples are possible? Please answer in details.
Draw the lines-shade out a feasable region : Maximize and minimize p = 2x-y with respect to x+y ≥ 2, x+y ≤ 10, x-y ≥ -2 and x-y ≤ 2. (Draw the lines, shade out a feasable region, look at boundary points)
Create an access form that has an interactive component : Create a PowerPoint presentation, it should include data from the reports you created as well as recommendations for how best to address the length of wait times in the ER.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Design a combinational circuit that compares unsigned number

Design a combinational circuit that compares two 4-bit unsigned numbers A and B to see whether B is greater than A. The circuit has one output X, so that X = 1 if A = B.

  Determine the maximum and minimum values of the source kva

A direct current source is required to supply a controlled current of 20A to a load in which the resistance varies from 0 to 12 ?. The source consists of a 208 V(L-L) , 60 Hz , there -phases , a controlled bridge rectifier, and a large series indu..

  Determine the transfer function h of the system

a signal x(t) is transmitted through a distortionless lti channel with a time delay of 12 msec. the energy of the output signal y(t) is related to the energy of the input signal by Ey/Ex =.04

  Is there any advantage or disadvantages to a type of memory

A new 24-bit processor is being designed for operation in a cell phone (you can assume the word-size is 24 bits). Suppose the following memory values are being stored in memory that is organized where each location is 8-bits wide (byte addressable..

  Determine the contact resistor that can go on the base

(a) determine the contact resistor that can go on the base if the length of the contact is 10 * Wb. (b) Plot the change in conductance in relation to varying the doping from 1014/cm3 to 1018/cm3 at room temperature. Redo the graph at 77K;

  How many bytes of data can we store in the memory

If we use the PC-relative addressing mode, and want to allow control transfer between instructions up to 50 locations away, how many bits of a branch instruction are needed to specify the PC-relative offset

  Determine the charge on the capacitor at any time t

A circuit has in series an electromotive force given b E(t) = 5sin 100t V, a resistor of 10 Ω, an inductor of 0.05 H, and acapacitor of 2 x 10-4 farads. If the initial current andthe initial charge on the capacitor are both zero, find the chargeon..

  What will be the voltage measured across the motor terminals

Suppose a resistor whose value is equal to the motor resistance is connected across the motor terminals and the motor is spun at 200 RPMs. What will be the voltage measured across the motor terminals

  How does the amplitude setting on function generator relate

With respect to sinusoidal signals, explain the difference between the way we normally define "amplitude" and the "amplitude" measurement on an oscilloscope. Also, How does the amplitude setting on a function generator relate to these

  Explain basics problems of induction motor

Basics problems of Induction motor, The frequency of the induced rotor currents in the rotor of a 60 Hz induction, machine is 2 Hz. Furthermore, the fields in the air gap turn at -40 rpm with respect to the rotor.

  Describe how would use the combination of short pass filter

Describe how you would use the combination of a short pass filter, a long pass filter, an amplifier and a mechanicalchopper to amplify a 5 mV signal to a 50 mV signal and remove noisefrom the original 5 mV signal.

  Derive minimum-cost realization of four variable functions

Derive a minimum-cost realization of the four variable function that is equal to 1 if exactly two or exactly three of it variables are equal to 1; ohterwise it is equal to 0

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd