Write down the laplace equation for equation

Assignment Help Mechanical Engineering
Reference no: EM13943701

1. A thermocouple is a device commonly used to measure the temperature in, for example, boilers and engines. It has the advantage of directly giving out a voltage that is approximately proportional to the measured temperature. The thermo-voltage is, however, only a few millivolts.

In the block diagram of FIGURE 4, the output of the thermocouple, vT(t), is fed into an amplifier to give a sufficiently large signal to drive a signal processing stage. The signal processing stage includes an analogue-to-digital converter (ADC) to give an output to drive a digital display. A low-pass filter (LPF) is placed between the amplifier and the signal processing stage to remove noise that may be picked up from adjacent 'noisy' equipment and from 'mains' interference.

471_m1.png

The thermocouple should ideally have a step change output to a step change in temperature. In practice this is not the case because the mass of the device introduces a thermal delay as it warms up or cools down to a new temperature. It can be shown that the temperature of the thermocouple is related to a step change in temperature by the equation:

1476_m2.png

The time constant depends upon the mass (in) and surface area (A) of the thermocouple, the thermal specific heat (c) of the material it is made from and also the heat transfer coefficient (h) between the thermocouple and its surroundings. Thus:

ζ= mc/Ah

2. (a) In FIGURE 5(a) the thermocouple is shown with an initial temperature the same as that for the ambient air, TA. It is then immersed into a tub of hot water at a constant temperature of Tw. Thus the applied step change in temperature is ΔT = Tw - TA.

(i) Write down the Laplace equation for equation (1).

(ii) Hence obtain the equation of the transient response of the thermocouple.

(iii) Plot the transient response using the data in TABLE B over a time period of about 4ζ.

979_table.png

Reference no: EM13943701

Questions Cloud

The balance in accounts receivable at january : The Company normally collects 60% in the month of sale and 30% in the month following the sale. Ten percent of all sales are uncollectible and are written off in the following month.
Know your vpn building blocks : Analyze the basic protocols involved in establishing a site-to-site VPN connection between two or more sites. Compare and contrast the differences between SSL-based VPNs and client-based VPNs. Describe cost benefits, ease of use, ease of management..
What is the intrinsic value of a share of xyrong stock : The risk-free rate of return is 6.5%, the expected rate of return on the market portfolio is 13%, and the stock of Xyrong Corporation has a beta coefficient of 2.7. Xyrong pays out 50% of its earnings in dividends, and the latest earnings announced w..
Training plan and area of focus guidelines : For Milestone Two, you will submit a written report in which you discuss how you will approach training the new technical Mobile Division management team and communicating the new guidelines to existing employees.
Write down the laplace equation for equation : In FIGURE 5(a) the thermocouple is shown with an initial temperature the same as that for the ambient air, TA. It is then immersed into a tub of hot water at a constant temperature of Tw. Thus the applied step change in temperature is ΔT = Tw - TA..
Provide a definition of operations management : To achieve a Pass you must provide a definition of operations management. You must also identify and discuss the four types of advantages that operations management contributes to various organisations.
Write a java application that performs the following task : Display a message whether the user input has been found in the array, at what position, and how many steps the program required to search for the data value.
Gravimetric composition and properties : -12 the gravimetric composition and properties of two different typical fuels i.e. coal and fuel oil is tabulated below- Parameters coal fuel oil Composition weight% -- C 76 85 H 4.5 11.5 S 0.5 3.5 N 1.0 -- O 3.0
Analysis of the company financial : Find or create their financials. Provide an analysis of the company's financial. With that information in mind, recommend a portfolio of investment instruments with specific names of each invest and explain why you are making the recommendations.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd