Write down am signal and sketch resulting am signal waveform

Assignment Help Electrical Engineering
Reference no: EM13272728

Consider the message signal m(t) = 20 cos(2πt) and the carrier signal c(t) = 50 cos(100πt). Write down the AM signal, and sketch the resulting AM signal waveform for 75 percent modulation.

Reference no: EM13272728

Questions Cloud

To what angle does each ball rebound : A 150g steel ball and a 300g steel ball each hang from 1.0-m-long strings. At rest, the balls hang side by side, barely touching. To what angle does each ball rebound
Explain if an artificial heart is capable of pumping : If an artificial heart is capable of pumping at least 57,000,000 pints of blood before failure, how long, in years, will it probably last in a patient whose average heart rate is 72 beats per minute and an average stroke volume (the amount of bloo..
Construct the circuit diagram of a decade counter : Decade counter: A decade counter is a counter circuit that counts from 0 to 9 (from 0000 to 1001 in binary numbers) and then resets. Using a 4-bit ripple counter block, 2 inverters and a 4-input AND gate, construct the circuit diagram of a decade ..
Summarize the plot of the play in terms : What is the setting of the play, in terms of the time period, region and weather? Explain the condition of the house. What emotional response does the setting evoke in you?
Write down am signal and sketch resulting am signal waveform : Consider the message signal m(t) = 20 cos(2πt) and the carrier signal c(t) = 50 cos(100πt). Write down the AM signal, and sketch the resulting AM signal waveform for 75 percent modulation.
Explain element and compound and homogeneous mixture : Classify each of the following as an element, compound, homogeneous mixture, or heterogeneous mixture.
Determine the tranfer function of the thermocouple : During calibration, and iron/constantan thermocouple is zeroed( set to emit a Zero Voltage) AT 0 DEGREES CELCIUS. At 750 degrees celcius, it emits a voltage of 38.8mV. Alinear Out/input relationships exists between 0 and 750 degrees celcius.
Compute the length of the rod : A thin uniform rod (mass = 1.95 kg) swings about an axis that passes through one end of the rod, What is the length of the rod
Plot in time of 4 periods approximate signals using 81 terms : The periodic signal x(t) is dened in one period as x(t) = te^-t; 0

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Explain the dilation-erosion-closing and opening operations

explain the dilation, erosion, closing, and opening operations on a binary image B with a structured element S. ( you need to use the symbolic notion for the operators, but need not provide the precise mathematical definitions

  Find the damping ratio and undamped natural frequency

How to find the damping ratio and undamped natural frequency given a 2nd-order differential equation.

  Find the frequency of the wave along with the permitivity

A wave in free space has a wavelength of 12 cm. This wave reaches a material in which the transmitted wave has a wavelength of 8 cm. lEl= 10V/m and lHl= 100 mA/m. Find the frequency of the wave, along with the permitivity and permeability of the m..

  Indicate which bits are the sign-exponent and fraction

Convert the value: $2103.25 using an IEEE standard 4 byte (32 bit) float floating point number representation. Identify every bit of the 32 bit number holding this record by first converting the number 2103.25 from decimal to binary

  Determine required sampling rate and the line speed

Consider a PCM-TDM system in which 24 signals are to be processed. Each signal has a baseband bandwidth of 3 KHz. The sampling rate has to be 33.3% higher than the theoretical minimum, and 8 bits are to be used.

  Evaluate the component selection for the differentiator

Evaluate the component selection for the differentiator and integrator amplifiers and their impact on the mahematical equation for each. Items for you to consider and discuss are Do you observe any limitation factors for the component parameters an..

  Find the average power dissipated in the soldering iron

The heating element in a soldering iron has a resistance of 30-ohm. Find the average power dissipated in the soldering iron if it is connected to a voltage source of 117 V rms.

  Determine whether operation results in overflow or underflow

Overflow occurs when a result is too large to be represented accurately given a word size. Underflow occurs when a result is too small to be represented correctly (for example, a negative result while doing unsigned arithmetic.).

  Does the discrete-time fourier transform exist

Consider the following signal y[n]; y[n] = X1[n+3] * X2[n] The signals X1 and X2 are defined as X1[n]=((1/2)^n) u[n] X2[n]= ((1/3)^n u[n] Determine the Z transform of y[n].

  What is the maximun temperature that the device may operate

A GaAs device is dopeed with a donor concentration of 3*10^15 cm^-3, For the device to operate properly, the intrinsic carrier cconcentration must remain less than 5 percent of the total electron concentration.

  Draw ac equivalent ckt with load impedance element equated

A three phase 4.157kv 60hz power system serves a 2880kva load pf=.8 lagging. Draw the ac equivalent circuit with load impedance element equated. The load is delta connected. solve for all the current (6 total).

  Determine which of the properties to hold or dont hold

Determine which of these properties hold or don't hold for the following discrete time systems. Justify your answers. IN each example, y(t) denotes the system output and x(t) denotes the system input.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd