Write an expression for the time dependence of current

Assignment Help Electrical Engineering
Reference no: EM13284472

From the equation for intermediate frequencies, what is thephase angle between the current and electric fieldwhen ωτ = 1, 0.1, and 10? For each case, write anexpression for the time dependence of current if the electric fieldvaries as sin(ωτ).

Reference no: EM13284472

Questions Cloud

What are the phasor angles of on simple rc series circuit : On a simple RC series circuit, with three voltages, Vin, Vc, Vr.Where Vin = Vc + Vr. With C = 0.047microfarads, Vin = 5
How long does it take for the ball to reach the wall : In a friendly game of handball, you hit the ball essentially at ground level and send it toward the wall with a speed of 15 m/s at an angle of 32° above the horizontal. How long does it take for the ball to reach the wall if it is 4.2 m away
Draw a circuit that shifts cyclically a register to left : Draw a circuit that shifts cyclically a register to left or toright ans is also able to preserve this register's state. Given aretwo controls C1 and C2 that select any of these three operations.use only NOT, AND and OR gates and D type flip flop.
Explain what is the molarity of the hcl aq : If 25.0 ml of 0.150 M Ba(OH)2 is required to react completely with 45.0 ml HCl solution, what is the molarity of the HCl(aq)
Write an expression for the time dependence of current : From the equation for intermediate frequencies, what is thephase angle between the current and electric fieldwhen ωτ = 1, 0.1, and 10. For each case, write an expression for the time dependence of current if the electric fieldvaries as sin(ωτ).
Define hydrochloric acid is added to zinc : Hydrochloric acid is added to zinc. How many mls of 0.500 M HCl are needed to react completely with 25.0 g of zinc metal
Explain what will be the total volume of solution : What will be the total volume of solution, in ml, when the concentration of 175.0 ml of 0.100 M K3PO4 solution is decreased to 0.012M
Evaluate the molarity of a solution made by dissolving : What is the molarity of a solution made by dissolving 45.3 g of potassium nitrate KNO3 in enough water to make 225 ml of solution
Determine what is the induced emf in the armature : A 12-kW, 120-V dc series generator has a series field resistance of 0.05 Ω. The generaated emf is 135V when the generator delivers the rated load at its rated terminal voltage. What is the armature resistance

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find how long will the cassette operate at normal power

The four alkaline battery cells store a total of 200watt-seconds of energy. If the cassette player is drawing a constant 10mA from the battery pack, how long will the cassette operate at normal power

  What is the capacitance of the capacitor in microfarads

An 80KHz sinusoidal voltage has zero phase angle and a maximum amplitude of 20 mV. When this voltage is applied across the terminals of a capacitor, the resulting steady state current has a maximum amplitude of 0.7 mA.

  Determine the number of resistors and current in each branch

A certain parallel resistor circuit consists of only ½ W resistors. The total resistance is 1.0 k-ohm, and the total current is 50 mA. If each resistor is operating at one-half its maximum power level

  How long does it take to send 1million bits of data

If each packet carries 1000 bitsof data, the distance between the sender and receiver is 5000km,link speed is 1Mbps, and the propagation speed is2x108 m/s. Assume no data or control frame is lostor damaged. Ignore transmission time for ACK.

  Will dc output voltage be higher or lower than dc voltage

A parallel circuit contains an AC voltage source of 3 Vrms, 100 Hz. The output of the voltage source is connected to a diode (1N4004). After the diode, connected in parallel are a 0.1uF capacitor and a 100 kohm resistor.

  Calculate the current through the circuit and voltage drop

Two ideal p-n junction diodes are connected in series across a 1 V battery such that both of them are forward biased (draw this). One diode has I0 = 10-5 A and another I0 = 10-8 A.

  Define important information about electrical networks

Important information about Electrical Networks, Engine consumes 5kw of power and a reactive power of 2kvar at current of (3+j2) Amps.

  Explain concept of differential encoding for bpsk modulation

a) What is the key difference between coherent and non-coherent demodulation b) Explain the concept of differential encoding for BPSK modulation.

  Explain sr flip flop from d flip flops

SR flip flop from D Flip flops, Show how to build a rising edge triggered SR flip-flop using a rising edge triggered D flip-flop and combinational logic.

  Write code-prompts user to enter his or her height in inches

Create a complete C++ program that prompts the user to enter his or her height in inches and outputs the following: Output "Height is six feet or more." when the user's height is 6 feet or more. Output "Height is less than five feet."

  Ndicate output frequenciesif the signal is applied to dsb

A modulating signal consists of two sinusoidal components: 1 kHz and 3 kHz. The transmitter carrier frequency is 80 kHz. If the signal is applied to an ideal DSB transmitter, indicate the output frequencies (in kHz).

  Evaluate the pros and cons of using the snr and signal

Which of these metrics are dependent on link conditions: CINR, SNR, or BER Evaluate the pros and cons of using the SNR and signal - to - interference - noise ratio ( SINR ) for estimating signal quality versus using the absolute value of the signa..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd