Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A saw, fan, and lube pump all go on when a start button is pressed. Pressing a stop button immediately stops the saw but allows the fan to continue operating. The fan is to run for an additional 5 seconds after shutdown of the saw. If the saw has operated for more than 20 seconds, the fan should remain on until reset by a separate fan reset button. If the saw has operated less than 20 seconds, the lube pump should go off when the saw is turned off. However, if the saw has operated for more than 20 seconds, the lube pump should remain on for an additional 10 seconds after the saw is turned off. Write a program that will implement this process.
initially at a temperature of 17c and a pressure of 100 kpa air occupies a volume of 3.0 m 3 in a rigid vessel.a valve opens allowing air at 600 kpa and 17c to enter until equilibrium is reached final temperature is found to be 77c
A 20 uF capacitor has a voltage of 12V across it at t=0. If a constant current of 4mA flows through the capacitor in the non-passive direction, how long will it take for all of the energy to be drained from the capacitor
In region 1, defined by z>0, there is a magnetic field of H= 4.8x ˆ 6y ˆ +8z (A/m) and the relative permeability is 50. Determine the magnetic flux density B in region 2, z
A wave propagates 50m through a dielectric of region 1. Region 1 is lossy. Here, f= 0.6 Np/m. At an interface to region 2, the reflection coefficient is r =0.2+j0.5. The wave then propagates 50m back into region 1 from where it originated.
the Mars Rover Spirit got stuck in the Martian sand. The wheels kept slipping. Attempts to free it were futile. Discuss the type of actuator in this case. Can you suggest any improvements in the actuator that would have prevented this unfortunate ..
given a sequence x(n), where x(0) = 4, x(1) =3, x(2) = 2, and x(3) =1 with the last two data zero-padded as x(4) =0, and x(5) = 0, evaluate its DFT x(k)
Construct a table showing the current for values of time between 0 and 9 hours at intervals of 1 hour.Hence draw a graph of i against t for 0 is smaller or equal to t is smaller or equal 9.(cannot type in proper inequality symbols)
(1) What would an amplifier with a gain of less than 1 be used for (2) (a) Do you think that the inverting amplifier is better than the non-inverting amplifier (b) Is there an advantage of using one versus the other (c) Does it matter
The tuning capacitor of a Wien bridge oscillator is 100 pF and the frequency is 5 kHz. To what value of capacitance pF should the capacitor be changed to if the frequency is to be changed to 2 kHz
A person shuffling across a dry carpet can be approximately modeled as a charged100-pF capacitance with one end grounded. If the person touches a grounded metallic object such as a water faucet.
write an 8051 program that would generate a 200khz, 50% duty cycle, square wave at P1.0.Use Timer 0 for the delay. Ignore the overheads cycles due to the instructions in the loop. Assume 12 MHz clock. All data must be hex.
What is frequency sensitivity of the demodulator? What is the value of A_m for which the carrier component is reduced to zero for the second time
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd