Write a computer program that plots the contour lines of

Assignment Help Mechanical Engineering
Reference no: EM13630906

Write a computer program that plots the contour lines of (sigma(1), sigma(2)) on a 2d rectangular beam. Sigma represents the shear stress. The beam(Length=1000 mm, height=100mm) has a load of P=2000N on the far left. The far right side of the beam is welded to a wall. Only about 10 contour lines are needed and the commands meshgrid and countour plot will be used. comment if you have further questions or need clarification.

Reference no: EM13630906

Questions Cloud

The wall system is 6m wide by 28m high what is the rate : a wall constructed of three layers is to be considered. the inner surface of the wall is maintained at 23 c and the
A hollow conducting sphere inner radius ra 18cm and outer : a hollow conducting sphere inner radius ra 18cm and outer radius rb24cm has a charge of -3.7n c is placed on the
An initially empty canister of volume 02 m3 is filled with : an initially empty canister of volume 0.2 m3 is filled with co2 from a line at 800 kpa 400 k. assume the process runs
Two air flows are combined to a single flow flow one is 1 : two air flows are combined to a single flow. flow one is 1 m3s at 293 k and the other is 2 m3s at 473k both at 1 bar.
Write a computer program that plots the contour lines of : write a computer program that plots the contour lines of sigma1 sigma2 on a 2d rectangular beam. sigma represents the
A pipe of length 080m is opened at both ends if the : a pipe of length 0.80m is opened at both ends. if the fundamental frequency of this pipe is 340 hz. what would be its
An ideal gas carnot cycle with air in a piston cylinder : an ideal gas carnot cycle with air in a piston cylinder has a high temperature of 1200 k and a heat rejection at 400 k.
Determine the tower height required to remove 90 of co2 : determine the tower height required to remove 90 of co2 from air by water in a dilute solution in a packed tower with a
Zyton corp budgets production of 292 units in january and : zyton corp. budgets production of 292 units in january and 264 units in february. each finished unit requires five

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd