Will sheet rust through within in the scratched condition

Assignment Help Mechanical Engineering
Reference no: EM13992476

A sheet of steel of thickness 0.50mm is tinplated on both sides and subjected to a corrosive environment. During service, the tinplate becomes scratched, so that steel is exposed over 0.5% of the area of the sheet. Under these conditions it is estimated that the current consumed at the tinned surface by the oxygen-reduction reaction is 2 X 18" A m-1. Will the sheet rust through within 5 years in the scratched condition? The density of steel is 7.87Mgm-3. Assume that the steel corrodes to give Fez+ ions. The atomic weight of iron is 55.9.

Reference no: EM13992476

Questions Cloud

Operate business solutions : After the success of the company's first two months, Santana Rey continues to operate Business Solutions. The November 30, 2015, unadjusted trial balance of Business Solutions (reflecting its transactions for October and November of 2015) follows.
Describe what fraud is and how it could be conducted : In conversations with PVSS, you have talked about the long-term strategic goals and plans for expansion.
What was snos ositionin strate : Identify, describe and define the marketing terms of consumers - Write a consumer profile of the target segments.
Estimate the percentage of an employee salary : Estimate the percentage of an employee's salary that must be contributed to the pension plan if it is to remain solvent. (Hint: Do all calculations in real rather than nominal dollars.)
Will sheet rust through within in the scratched condition : Under these conditions it is estimated that the current consumed at the tinned surface by the oxygen-reduction reaction is 2 X 18" A m-1. Will the sheet rust through within 5 years in the scratched condition? The density of steel is 7.87Mgm-3. Ass..
Explain the results of the improvements you recommended : Post:Name the product and the associated password management protocol you selected. Analyse the good and bad practices of this protocol.
How does the shape of the foil affect the capacitance : How does the shape of the foil affect the capacitance? Would it still be a capacitor if the foil and mylar took on a different shape; say for example if the top sheet of foil were crumpled into a ball?
Create an intervention for addicts : You have been assigned an internship at a drug rehab center in downtown Baltimore. One of your assignments is to create an intervention for addicts who are between the ages of 18 to 24
Explain why you selected that violation to discuss : Create an initial post in which you analyse an act within your country with the purpose of protecting data. Focus on how your selected act protects data.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd