Why sludge system is operated at relatively low flood ratio

Assignment Help Civil Engineering
Reference no: EM13318722

State the two main reasons why an activated sludge system is operated at a relatively low food/microorganism ratio.

Reference no: EM13318722

Questions Cloud

Determine the activated sludge aeration volume required : Determine the activated sludge aeration volume required to treat 2.64 mgd with a BOD of 120 mg/l based on the criteria of a maximum BOD loading of 40 lb/1000 ft cubed/day and a minimum aeration period of 5 hr.
Calculate the surface area required for a stabilization pond : Calculate the surface area required for a stabilization pond to serve a domestic population of 1000. Assume 80 gpcd at 210 mg/l of BOD. Use a design loading of 20 lb of BOD/acre/day.
Calculate the bod loading and days of winter storage : Calculate the BOD loading and days of winter storage available between the 0.6 and 1.5 m depths, assuming a daily water loss of 0.30 cm by evaporation and seepage.
What is the minimum non zero thickness of the oil : A thin layer of oil (n=1.25) is floating on water (n=1.33). What is the minimum non zero thickness of the oil in the region
Why sludge system is operated at relatively low flood ratio : State the two main reasons why an activated sludge system is operated at a relatively low food/microorganism ratio.
Calculate the diameter of the hole : A large storage tank, open to the atmosphere at the top and filled with water, calculate The diameter of the hole
Find the magnitude of the average emf : A 127-turn circular coil of radius 2.09 cm is immersed in a uniform magnetic field that is perpendicular to the plane of the coil. Find the magnitude of the average EMF
Calculate the inductive reactance and the rms current : In a purely inductive AC circuit, L=25.0 mH and the rms voltage is 150 V. Calculate the inductive reactance and the rms current in the circuit
Explain the standard heat of reaction for sugar and ethanol : What is the standard heat of reaction for- sugar and ethanol are "burned" to water vapor and carbon dioxide?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find out the number of turns in each spring

Find out the number of turns in each spring, if the diameter of the spring wire 14 mm and the diameter of coil is 80 mm. Assume C=84 GN/mmxmm.

  Determine what was the distance between the markers

A 100 ft cut steel tape was used to measure between two property markers. The rear surveyor held 93 ft, while the head surveyor cut .67ft. What was the distance between the markers

  Determine the basin dimensions

Determine the basin dimensions (width, length, depth) for a detention time of 3 hours and a length to width ratio of 4 to 1. (use English units)

  Estimate amount of lime required for specified ferric dose

estimate the mass and volume of sludge produced from unreated wastewater without and with the use of ferric chloride for the enhanced removal of TSS. Also, estimate the amount of lime required for the specified ferric schloride dose.

  Importance of mineral identification in applications

What are minerals? Sketch different types of mineral crystal forms and list different types of rock forming minerals. Describe with examples the importance of mineral identification in engineering applications.

  Determine the isentropic efficiency of the turbine

Steam enters an adiabatic turbine steadily at 3 MPa and 300 *C and leaves at 70 Kpa and 100 *C. If the power output of the turbine is 2 MW, determine a) the isentropic efficiency of the turbine and b) the mass flow rate of the steam flowing throug..

  Determine the maximum and torsional shear stress

A thin-walled circular tube has an average diameter of 100 mm and a wall thickness of 4 mm. It is subject to torque of 4 kNm and a compressive axial force of 40 kN.

  Determine tension in rope ab required for static equilibrium

The frame is designed to carry the hanging mass at G equal to 167 kg. The frame is supported by a pin connection at C and the rope AB, and constructed with pin connections at points E, F, and D. Importantly, members BEFG and EDC are continuous mem..

  Find profitable blend of alloys that will satify requirement

Suppose a specialty steel company receives an order for 200 tons of steel containing at least 3 percent nickel and 2 percent manganese, with a carbon content not exceeding 3.5 percent. The steel will sell for $25 a ton.

  Determine capitalized cost of project of city development

The lubbock board of city development has decided to ask the city council to construct a tunnel under the snowcapped mountain range east to downtown lubbock so that out of town visitors can reach historic prairie dog town.

  What are the velocities of both just before and after impact

What are the velocities of both just before impact and just after impact. There is a distance of 5m between the vehicles prior to the winch being turned on.

  Determine the the max weight of the block

Determine the the max weight of the block that the system does not fail if the max tension that can be developed in cable DB is 100N and the max compression that can be developed in tower CD is 100N.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd