Why radio waves is chosen for remote/close rangetransmissio

Assignment Help Electrical Engineering
Reference no: EM13862766

Why radio waves is chosen for remote/close range Transmission ? and How to Construct a simple radio receiver ? 

 

 

Reference no: EM13862766

Questions Cloud

Bipolar junction transistor : Find V., Vb, Vet /ID, lc, and le for each of following bipolar junction transistor .circuits . All transistors have Vbe= o . 7 volts Fs 100
Prepare journal entries to record each of these transactions : Prepare a trail balance on the trial balance tab. Be sure the trial balance is in balance, that the total debits equal the total credits. Do not proceed to the next step until the trial balance balances.
What part of florence''s problem is a mezzo-level problem? : What part of Florence's problem is a mezzo-level problem?
Determining that behavior is disturbed or abnormal : Psychologists may use a combination of these criteria for determining that behavior is disturbed or abnormal. Of the seven criteria for abnormal behavior, which two do you think are most valid? Which two are the least valid
Why radio waves is chosen for remote/close rangetransmissio : Why radio waves is chosen for remote/close range Transmission ? and How to Construct a simple radio receiver ?
Two unlabeled boxes contain kcl and cscl : 1.    (35) Two unlabeled boxes contain KCl and CsCl for analysis using XRD. The diffraction maxima are observed from the (111) planes, using X-rays of wavelength 0.0862 nm. a.    What is the diffracted beam angle, q (with respect to the plane) for b..
Do violent video games contribute to youth violence? : Do violent video games contribute to youth violence?
Would this action by claude meyer be possible : Would this action by Claude Meyer be possible under international financial standards (IFRS) why or why not?
Show how the lottery winning affect your budget line : You have just won $100,000 lottery. Use a diagram showing the tradeoff between leisure ( on x-axis) and goods (y-axis) for the following: Show how the lottery winning affect your budget line

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine rated current and voltage for high and low sides

a single phase 100 kVA, 1000/100 V transformer gives the following test results: Open Circuit test: 100V, 6.0 A and 400 W Short Circuit test: 50V, 100A and 1800W determine the rated current and voltage for high and low sides

  Determine the flux density in the core

a magnetic circuit has a mean length of 0.80 m, a cross-sectional area of 0.06 m^2, and a relative permeability of 2167. connecting its 340-turn 64-ohm magnetizing coil to a DC circuit causes a 56-V drop across the coil. determine the flux density..

  Find the extension and retraction load-carrying capacities

An 8cm diameter hydraulic cylinder has a 4cm diameter rod. If the cylinder receives flow at 100Lpm and 12MPa, find the a) Extension and retraction speeds b) Extension and retraction load-carrying capacities

  Describe the oscillations in electric circuits

The following functions describe the oscillations in electric circuits and the vibrations of machines and structures. Plot these functions on the same plot. Because they are similar decide how best to plot and label them to avoid confusion.

  Determine the transfer function of the designed fir system

Design a 3-tap FIR lowpass filter with a cutoff frequency of 1,500 Hz and a sampling rate of 8,000 Hz using a. rectangular window function b. Hamming window function.

  How many turns are required for a circular loop

How many turns are required for a circular loop of 100-mm radius to develop a peak emf of 10mV if the loop rotates 30r/s in the earth's magnetic field Take B = 60E-6T.

  Design a moore sequential circuit to control the lights

As indicated from the diagram, when LEFT = 1 the lights flash in a pattern LA on; LA and LB on; LA, LB, and LC on;all off; and then the sequence repeats. When RIGHT = 1, the lightsequence is similar. If a switch fromt LEFT to RIGHT (or viceversa) ..

  Find total impedance of network if frequency is given

In a circuit, there is a resister, a conductor and a capacitor connected to voltage source. R = 25 ohms, L = 20 milliH, and C = 50 microF. a) Find the total impedance of the network if the frequency is 60 Hz.

  Find the work done in moving a point charge 2c

(a)find the work done in moving a point charge +2C from (2,0,0) to (0,2,0) and then from (0,0,0) to (0,2,0). (b)find the work done in moving a point charge +2C from (2,0,0) to (0,2,0) along the straight-line path joining the two points.

  Calculate e directly by superimposing the e fields due to q

In spherical Coordinates the potential of a dipole lacated at the origin is given by: a) use  \(E = -grad \phi\) and the above to calculate E for a dipole located in free space.

  Which direction to simplify resistance for thevenin r

In step four of this problem, how do you know in which direction to simplify the resistance for the thevenin resistance. (since you come up with a different answer depending on which direction you choose to simplify from)

  What magnitude of dipole strength has to be associated

A certain sample of pure quartz has a dielectric constant of 3.8, dielectric strength of 1.0 kV/0.0010 in, and a density of 2.6 Mg/m3. Assume the number density of dipoles in quartz is the same as the number density of SiO2 units.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd