Why must an e-mosfet be handled with care

Assignment Help Electrical Engineering
Reference no: EM131282576

1. Why must an E-MOSFET be handled with care?

2. Why is a thin metal wire connected around all the leads of a MOSFET during shipment?

3. What are some precautionary measures that are taken while working with MOS devices?

4. Why would a designer generally select a MOSFET over a BJT for a power-switching function in a switching power supply?

Reference no: EM131282576

Questions Cloud

Advantages and disadvantages of bjt and fet amplifiers : Draw any circuit that shows a power FET controlling a large load current. Explain the off -on action. Include RDS(on) in your discussion.
What economic and societal factors affect the demand : How has the emergence of different types of health insurance plans-FFS, health maintenance organizations (HMOs), preferred provider organizations (PPOs), and capitation-affected the trends in healthcare services today?What economic and societal fa..
Show that three symbols constitute a simplex code : Consider a set of three equally likely symbols whose signal constellation consists of the vertices of an equilateral triangle. Show that these three symbols constitute a simplex code.
Discuss the european unions effort at monetary union : Discuss the European Union's effort at monetary union. Which countries are participating? How might that affect these countries? Other countries? Give two examples that support your ideas.
Why must an e-mosfet be handled with care : Why would a designer generally select a MOSFET over a BJT for a power-switching function in a switching power supply?
Derive the ols estimates : Derive the OLS estimates βˆ1 and βˆ2 (note that I am asking for the actual number values of βˆ1 and βˆ2. This can be done, even though I haven't given you the complete dataset. There are multiple ways to do this). What would the RSS be equal to? Why..
Who has the responsibility for the health care of the people : Did the World Bank and other international donors act responsibly and ethically in constraining their humanitarian assistance? Who has the responsibility for the health care of the Latin American people?
Identify and explain at least three challenges : From an executive's position, identify and explain at least three challenges and opportunities that might face an international executive over the next five years.
What is the voltage v that turns on the diode : If the breakover voltage of Fig. 13-40a changes to 20 V and the holding current changes to 3 mA, what is the voltage V that turns on the diode? What is the voltage that turns it off ?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine what must the unity gain of the op amp be

It is required to design a noninverting amplifier with a dc gain of10. When a step voltage of 100 mV is applied at the input, it isrequired that the output be within 1% of its final value of 1 V inat most 100 ns. What must the unity gain of the op..

  Determine the resulting number of bits

In a CD player,the sampling rate is 44.1KHz and the samples are quantised using a 16bit/sample quantizer. Determine the resulting number of bits for a piece of music with a duration of 50 minutes

  Find the alternating voltage and current in given circuit

Find the Alternating Voltage and Current in given circuit. For the parallel circuit below, solve for the RT, IT (pk), IT (p-p), IT (rms), IT (avg). Current in each branch i. IR1 (pk), IR1 (p-p), IR1 (rms), IR1 (avg).

  Describe when does computer a retransmit the message

The messages being sent are 2 milliseconds long. Computer A starts sending a message on the bus; 250 microseconds later, Computer B starts to send a message, and 250 microseconds after that, Computer C starts to send a message.

  Using determinants solve for the nodal voltages

Using the format approach, write the nodal equations for the networks of given figure.  - Is symmetry present? - Using determinants solve for the nodal voltages.

  Determine the maximum stress and the curvature of the bar

A couple of magnitude M is applied to a square bar of side a. For each of the orientations shown, determine the maximum stress and the curvature of the bar.

  Determine the maximum and minimum inductor currents

A flyback converter is to be designed to provide 10V at 18A from a smooth 200V source. Isolation between the input and output is required. The switching frequency is 200kHz and the duty cycle is 0.4.

  What is the difference between serial and parallel transfer

What is the difference between serial andparallel transfer. how to convert serial data to parallel andparallel data to serial. What type of register is needed.

  A starting torque of 80 nm is developed

A starting torque of 80 Nm is developed in an induction motor by an auto-transformer starter with a tapping of 30%. If the tapping of auto-transformer starter is 60% then the starting torque

  Calculate the maximum deflection angle for calcite

Calculate the maximum deflection angle for calcite based polarization beam deflector. no=1.658, ne=1.486

  What will the value of the current source be in ma

A voltage source Vs = 10 V is in series with a resistor of 10 kOhm. If the source transformation theorem is applied, what will the value of the current source be in mA

  Find the number of poles required

Find the number of poles required, when the frequency is 50Hz and speed of the induction motor is 500 rpm?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd