Why is bit stuffing needed on a can system

Assignment Help Electrical Engineering
Reference no: EM13249700

1. How much noise can be tolerated in a digital system using a 5 V power supply?

2.What functions does an H-bridge perform in controlling a small DC motor?

3.Explain how to calculate the duty cycle of a pulse in terms of frequency and width.

4.Explain how to calculate the duty cycle of a pulse in terms of frequency and width.

5.Why is bit stuffing needed on a CAN system?

6. A communications channel has a bandwidth of 1,000 Hz and a signal-to-noise ratio (SNR) of 40 dB. What is the maximum possible data rate?

Reference no: EM13249700

Questions Cloud

Find when does computer a retransmit the message : The messages being sent are 2 milliseconds long. Computer A starts sending a message on the bus; 250 microseconds later, Computer B starts to send a message, and 250 microseconds after that, Computer C starts to send a message.
Find the current in the loop : A single-turn circular loop of radius 5.5 cm is to produce a field at its center that will just cancel the earth's field of magnitude 0.7
Does the fact that there is no written partnership agreement : Currently, the partnership has no formal agreement that outlines profit distribution, managerial responsibilities, and liabilities of the parties. Joan and Don want to expand the business.
Explain what volume of naoh is required to precipitate : what volume of 0.100 M NaOH is required to precipitate all of the nickel (ll) ions from 150.0 mL of a 0.162 M solution of Ni(NO3)2
Why is bit stuffing needed on a can system : 1. How much noise can be tolerated in a digital system using a 5 V power supply 2.What functions does an H-bridge perform in controlling a small DC motor 3.Explain how to calculate the duty cycle of a pulse in terms of frequency and width.
Find the velocity of the water in both pipes : Water is flowing at 100 lbm / s in a circular drain pipe of 1 m in diameter. This 1 meter diameter pipe comes to an abrupt constriction when the diameter suddenly reduces to 1.5 feet, Find the velocity of the water in both pipes
Find the system transfer function of the system : Find the system transfer function H(s) = Y(s)/X(s) if the input x(t) and the output y(t) of the system are related by the equation y(t) + 3y(t) = x(t) - x(tau)d tau. Assume y(0) = 0.
Depict possible mesomeric structures of the carbocationic : Draw all possible mesomeric structures of the carbocationic intermediate in the chlorination of benzoic acid. Explain why the main product is m-chlorobenzoic acid.
Determine the wavelength of the unknown light : A Michelson interferometer splits a beam of light of unknown wavelength producing a bright fringe (i.e., all of the intensity) at the detector, What is the wavelength of the unknown light

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine values for a and b that will satisfy constraints

Suppose we want to construct an amplifier with a closed-loop gain of 50. We want the gain to vary by no more than +/- 5% while the open-loop gain varies by +/- 50%. Determine the values for a and b that will satisfy these constraints.

  What range of resistance values are limited by power

The maximum ratings for all resistors of this type are 250 (V) and ½ (W). What range of resistance values are limited by the maximum voltage rating of 250 (V), and what range of resistance values are limited by the maximum power of ½ (W)

  How does the darsonval movement work with voltmeter

how does the D'Arsonval movement work with voltmeter and ammeter i know how to design the cicuits but a little more of how the movement actually work in both cases. like for the ammeter the reason the resistor is place in parallel is to limit the ..

  What should thevenin equivalent resistance of power amplier

Suppose you are designing a power amplifier for a loudspeaker which has an equivalent resistance of 150 . What should be the Thevenin equivalent resistance of the power amplifier in order to maximize the power transfer to the loudspeaker

  Determine the sum or difference of two numbers

Use the simulation timing diagram to compare the worse case time to do an operation with your ALU with the worst case using the 74LS381. State which operation takes the longest and list the time required for both ALU's.

  Determine the charge and current flowing in the circuit

The capacitor in an RC circuit (R=10.0k Ohms and C=25.0uF) is initially uncharged. Determine the charge and current flowing in the circuit at 0.40 time constants (t=0.40 tau) after the circuit is connected to a 9.00 V battery.

  Presuming that ideal filters are available

Assuming that ideal filters are available, what is the lowest frequency at which the signal can be sampled and subsequently recovered in its analog form without distortion using a low pass filter?

  Give the solution to power factor

The solution to Power Factor, Two single-phase loads are connected in parallel across a 415 V, 50 Hz supply. One load is rated 130 kW at a power factor of 0.75

  At what time does he reached the dock

Once a week a wagon driver leaves his hut and drives his wagon to the river dock to pick up supplies for his town. At 4:05 PM, one-fifth of the way to the dock, he passes the Temple. At 4:15 PM, one-third of the way, he passes the Preetam-Da-Dhaba..

  Explain construct a table showing the current for values

Construct a table showing the current for values of time between 0 and 9 hours at intervals of 1 hour.Hence draw a graph of i against t for 0 is smaller or equal to t is smaller or equal 9.(cannot type in proper inequality symbols)

  What value of series resistance is needed to limit led

An LED is rated at VF=1.6V to 2.0V at IF=20mA. What value of series resistance is needed to limit the LED current to 20mA when this LED is connected to a 32 v peak source (that is, a source having a peak voltage of 32 v)

  Calculate the power factor at whic the source operates

In each of the three phases in a balanced delta- connected load is composed of a 10mF capacitor in parellel with a series-connected 470 ohm resistor and 4mH inductor combination, assume a phase voltage of 400 V at 50 Hz

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd