Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1. What are the functions of : a. Project manager. b. Project Superintendent c.Project Engineer d. Foreman e. Schedular f. Purchasing agent/expediter
2.What are the stages at which the designer will schedule design reviews?What is the purpose of the design review.Is there any impact from ignoring design review?What should a designer do when the owner is clearly incapable,through lack of staff or experience,of completing a component design review?
3.Why do owners prefer the design-build form of contracts when many of them know they can obtain better quality construction using other forms?
What additional data and information should he gather,and how should he go about gathering the data information ?
The motion of a particle on the surface of a right circular cylinder is defined by the relations, R = A, theta = 2pi(t), and z=Bsin(2pi)(nt), where A is a constant. Determine the magnitudes of the velocity and acceleration of the particle at any t..
The velocity of a particle traveling along a straight line is v=(3t^2-6t) ft/s , where t is in seconds. if s=4ft when t=0 determine the position of the particle when t=4s what is the total distance during the time interval t=0 to t=4s
Consider a system that consists of 4 devices. The probabilities of failure for each of the devices are, respectively: 10%, 25%, 20%, and 30%. (a) If these components were in series, what is the probability that the system operates
Heat transfer through the walls and roof is estimated to be 5 40 kJ/hr per degree temperature difference between the inside and outside. a. If the outside temperature in the winter is - 5 C, what power required to drive the heat pum p (kJ/hr
For a same soil, two moist densities and their corresponding degrees of saturation are given in the following table Density (kg/m^3) S(%) 1700 55 1800 70 What is the void ratio (e) and the specific gravity (Gs)?
A beryllium copper wire having diameter of 1-50 mm and length of 40mm is used as a small torsion bar in an instrument. determine what angle of twist would result in the wire when it is stressed to 250 mpa.
Two box culverts each is 0.61 m by 0.61 m and has n = 0.013, Ke = 0.05, Cd = 0.85, L = 30 m, So = 0.7%, and HW = 1.5 m. a. What is the design flow capacity for free outlet condition b. What is the design flow capacity for tailwater of TW = 1 m
Calculate the compacted cubic yards per hour if a compactor with a 5-ft drum width travels at 3 mph over a 10-in. lift of aggregate base course with 4 passes required to meet density specifications under average operating conditions.
disk of radius R=7 in. spins at a constant angular speed of w=500rpm in the clockwise direction. If the disk is released from rest far above the ground, what are the speed and acceleration of the disk's top C point after it has fallen h=3ft
CPM Construction plans to buy a truck for $150,000 and sell it for $15,000 at the end of 5 years. The annual operating cost of the vehicle is $60,000. What is the present value of the truck
A compressor pressurizes air from 1 atm to 2.38 atm at steady state. At the entry the air's temperature is 70F, whereas at the exit it has quadrupled (in degrees F). At the entry the air's volumetric flow rate is 17 ft3/s
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd