User Account

All Pages

Why are rf amplifiers necessary in fm receivers

Assignment Help Electrical Engineering
Reference no: EM13265996

1. What parameter of the intelligence signal causes or determines the rate of carrier frequency deviation?

2. If you are tuned to an FM station at a frequency of 100.1 MHz, show the bandwidth allocation for two adjacent stations.

3. What is the required BW to transmit an FM signal if the maximum deviation is 60 KHz and intelligence frequency is 15 KHz?

4. Determine the power distribution in carrier and sidebands if the transmitted power is 1,000 W and mf = 1

5. Why is Preemphasis required?

6. What is the RC time constant required for Preemphasis circuits?

7. An FM transmitter delivers to a 75 ohm antenna a signal voltage of
V(t) = 1000 sin ( 109t + 4 sin 104t )
Determine:

(a) Carrier frequency
(b) Intelligence frequency
(c) Modulation index
(d) Total power in FM signal
(e) Carrier power
(f) Power in each side band

7. Why are RF amplifiers necessary in FM receivers?

8. What are the two functions of a Limiter?

9. What is the meaning of the term center frequency in reference to FM broadcast?

10. What frequency swing is defined as 100 % modulation for an FM broadcast station?

11. Draw a block diagram for a Crossby FM transmitter for a transmitter frequency of 100.1 MHz.

Reference no: EM13265996

Questions Cloud

What are you going to say to make a lasting impression : An elevator with the President, Oprah, your CEO, or the person that just gave a great presentation at an industry conference. What are you going to say to make a lasting impression?
Find the normal force exerted on the rod by lower support : A thin rod of length 9.5 m and mass 16 kg is supported at a 28? incline. Find the normal force exerted on the rod by the lower support
Explain what is the molarity of all solutes in the solution : what is the molarity of all solutes in this solution. what is the osmotic pressure of the solution at 25 C. assume total dissociation of NaCL.
How much gasoline spills out in this case : Early in the morning, when the temperature is 5.0?C, gasoline is pumped into a car's 51-Lsteel gas tank until it is filled to the top.  How much gasoline spills out in this case
Why are rf amplifiers necessary in fm receivers : 1. What parameter of the intelligence signal causes or determines the rate of carrier frequency deviation 2. If you are tuned to an FM station at a frequency of 100.1 MHz, show the bandwidth allocation for two adjacent stations.
The percentage by weight of graphitein the original mixture : The volume of oxygen used was 747.0 milliliters at 1,092 K and12.00 atm pressure, Calculate the percentage by weight of graphitein the original mixture.
At what height should you center the pattern on the wall : You're an optometrist, mounting a projector at the back of your 4.2m -long exam room, 2.6 m above the floor. At what height should you center the pattern on the wall
Decisions makeing in a business environment : Decisions makeing in a business environment whether good or bad. For each article, write a short 1/2 page summary of the issue and what lessons can be learned. Please provide acrticle hyperlink
State what are the equilibrium partial pressures of each gas : An additional 31.4 g of water was added to the reaction vessel, and a new state of equilibrium was achieved. What are the equilibrium partial pressures of each gas in the mixture

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How much work is done upon the crate by friction

A 9.2 kg crate is pulled up an incline with initial speed of 1.2 m/s A pulling force of 105N is applied parallel to surface of incline which is at angle of 21.8 degrees to horizontal The coefficient of kinetic friction is .32 and crate is pulled d..

  Determine the frequency of input voltage v1 in hz

Given an AC input voltage of Vrms = 200Vrms and a sinusoidal frequency of omega = 120pi rad/sec, determine the following: V1peak (peak value of AC input voltage) V1(peak-to-Vpeak )(peak to peak value of AC input  voltage) Frequency of input voltage V..

  Explain scada system

Explain the function of the HMI in a SCADA system.

  Determine the resistance range for resistors with color code

1) Determine the resistance range for resistors with the following color codes: a. Red-Orange-Orange-Silver b. Gray-Red-Red-Gold c. Yellow-Purple-Yellow-Gold 2) Determine the color code for the f..

  Explain wavelength and frequency the downstream information

Wavelength and Frequency, The downstream information (from the network to the customer) is transmitted at a wavelength of 1550 nanometers and the upstream information

  Draw hardware logic diagram using and-or logic

Design a counter to count even numbers between 0 and 15. Therefore states will be 0 -> 2 -> 4 -> 6 -> 8 -> 10 -> 12 -> 14 -> 0. If any unused state is encountered bewteen 0 and 7, then the counter should go back to initial state 0.

  Which would be studied the benefit of placing the panels

Determine the number of colectors required and the cost of auxiliary power in a facility that provides hot water to a community of 34 residents. Which would be studied the benefit of placing the panels tilted at 18 degrees relative to the horizont..

  Control systems- operation of a pid

Control Systems: Operation of a PID, Which one of the following statement regarding to operation of a PID is true?

  Calculate the number of turns on transformers high side

a) The number of turns on its high side. b)The turns ratio when it is used as a step-down transformer. c) The turns ratio when it is used as a step-up transformer.

  How long in seconds would take to instead rotate degrees

If it takes 1 sec to rotate 45 degrees after starting from rest, how long in seconds would it take to instead rotate 81 degrees after starting from rest under the same constant angular acceleration.

  What is the output in binary number corresponding to input

Design a 3:2 priority encoder. It will take inputs D3, D2, and D1, and produce A1 and A0. If exactly one of the inputs is true, the output is the binary number corresponding to the input number (D3 -> 11, D2 -> 10, D1 -> 01).

  Calculate field on one side of disk as function of distance

Consider a thin ring of radius a with uniform charge density and total charge Q. The ring is cut in half across the diameter and the two halves superimposed to double the effective charge density.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd