Which software can help me to have a good simulation

Assignment Help Mechanical Engineering
Reference no: EM131032711

which software can help me to have a good Simulation of Direct Injection gas engine?Fire or fluent?

Reference no: EM131032711

Questions Cloud

How old are the astronauts when they send the signal : How large is the Earth's diameter as measured from the neutrino rest frame? Is this a proper length? Why or why not - Determine the total number of cycles that the laser light executes as it passes from the beam splitter to the mirror and back along..
Find the dft of the following discrete-time sequence : Find the DFT of the following discrete-time sequence
Draw a curve describing the evolution the output gap : EC 502: Problem Set 6. Using the formula for εts given above, together with the optimal policy formula for xt given above, draw a curve describing the evolution the output gap xt in response to the positive cost-push innovation in period 1. In period..
Explain the biological species concept : Explain the biological species concept. By definition, explain what separates one species from another. Then explain why it is not surprising that some species can interbreed with one another while others can not. (Keep in mind that the dog and ..
Which software can help me to have a good simulation : which software can help me to have a good Simulation
Write a review on emerging application of technology : Write a review on Emerging Application of Technology in a Critical Infrastructure. This paper is the second of two Technology Reviews that you will research and write for this course.
Determine the minimum value of r : Determine the minimum value of R and the corresponding value of x
Determine the enthalpy change and the entropy change : By accounting for the deviation from ideal-gas behavior through the use of generalized charts.
Description of potential generalizability of study results : Description of the statistical analysis used and the primary measures of association reported, Identification of potential confounders (if any) and the technique used to minimize them or analyze their effects

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Design practical fluid system

Prepare young engineers through hands on experience in writing project technical report to execute tasks related to design practical fluid system.

  What is the claimed efficiency of the engine

An inventor claims to have made an engine that operates from a plutonium energy source at 1060°R and a heat sink at 558°R. He also claims that the engine produces 4.80 hp while rejecting 16000 Btu/hr of heat.

  Knowing that the internal pressure is 350 kpa determine the

a spherical gas container made of steel has a 5-m outer diameter and a wall thickness of 6 mm. knowing that the

  If the machine is mounted on a large concrete block of mass

an industrial machine of mass 453.4kg is supported on springs with a static deflection of 0.508cm. the machine has a

  Calculate diameter of this steel rod when it is under load

A 1 m steel rod (circular cross-section) has a diameter of 2 cm and is pulled in tension with a load of 50 kN. The steel rod experiences an entirely elastic elongation of 1 mm. a) Calculate the elastic modulus of the steel. b) Calculate the diameter ..

  The currently used material is brass but you have decided

you are asked to design a solid circular shaft of minimum cost that is 1.3 m long and has to twist less than 3 degrees

  The pressure is held constant as the air cools to 50degc

consider the following setup that sits in a room with a surrounding temperature of 25degc. the pressure and temperature

  Calculate the ratio of the axial strain

Calculate the ratio of the axial strain to the hoop strain, assuming that the deformation is elastic. Assume that E = 107 psi and υ = 1/3. Does the length of the tube increase, decrease, or remain constant?

  Calculate the tensile stress required to cause yielding

if the critical resolved shear stress for yielding in aluminum is 240kpa. calculate the tensile stress required to cause yielding when the tensile axis is [001]

  Question 1 entropya in a coal fired thermal power station

question 1 entropya in a coal fired thermal power station indicate where the exergy contained in the coal is destroyed.

  If the driver first applies the brakes 150 ft from the tree

a car is traveling at sea level at 88 mihr on a 4 upgrade before the driver sees a fallen tree in the roadway 150 ft

  Problem regarding the martensite and austenite

Assume that this expansion occurs equally in all directions. For steel, the coef?cient of linear thermal expansion is α = 6 × 10-6/?C, Young's modulus is 30 × 106  psi, and υ = 0.29. Assume these apply to both  martensite and austenite. Find the stre..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd