Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A chemical engineer is considering two styles of pipes for moving distillate from a refinery to the tank farm. A small pipeline will cost less to purchase (including valves and other appurtenances) but will have a high head loss and, therefore, a higher pumping cost. The small pipeline will cost $1.7 million installed and will have an operating cost of $12,000 per month. A larger-diameter pipeline will cost $2.1 million installed, but its operating cost will be only $8000 per month. Which pipe size is more economical at an interest rate of 1% per month on the basis of an annual worth analysis? Assume the salvage value is 10% of the first cost for each pipeline at the end of the 10-year project period.
Thin rubber strips are used to provide increasing resistance to orthopedic patients during large motion exercises. The sheets shown are 0.03125 in thick and 3 in. wide. Say the rubber properties are 120 psi and v= 0.47.
A discharge of 2,200 ft^3/sec flows in a trapezoidal channel at a normal depth of 8.0 ft. The channel has a slope of 0.01, a 12-ft bottom width, and side slopes of 1:1 (H:V). Determine the manning coefficient of channel roughness
To remove the solution containing metal from a part after plating the part is commonly rinsed with water. The rinse water is contaminated with metal and must be treated before discharge. The Shiny Metal Plating Co. The plating solution contains 85..
Your boss has assigned you the job of designing a rapid-mix tank for the new water treatment plant for the town of Waffle. The design flow rate is 0.050 m^3/s. The average water temperature is 8 degrees celcius.
Near the point (x, z) =(3,2) in a flow with a zero y-component (v=0), the velocity component are described by u =3x-3z, and w = 6-4z+ x. The velocities u and w are in m/s and are in the x- and z- directions, respectively.
Measurements indicate that to cause this flow the force acting on the contents of the control volume is 40i lb. Determine the net rate of flow of linear momentum through the control surface.
If it absorbs 100 Joules each cycle from the hot reservoir, how much work does it do. How much heat is given off in each cycle If each cycle takes 0.5 seconds, find the power output of the engine.
Prove that the smallest angle of any triangulation of a convex polygon whose vertices lie on a circle is the same. This implies that any completion of the Delaunay triangulation of a set of points maximizes the minimum angle.
Part A Determine the tension developed in cable AB for equilibrium of the 350-lb crate Part B Determine the tension developed in cables AC for equilibrium of the 350-lb crate. Part C Determine the force developed along strut AD for equilibrium of ..
A gray silty clay (CL) is sampled from a depth of 12.5 feet. The "moist" soil was extruded ffrom a 6-inch high brass liner with an inside diameter of 2.83 inches and weighed 777 grams.
Derive an equation for the reaction force (Rx) associated with conservation of momentum in a straight length of pipe of uniform diameter. Approximate the velocity as steady and uniform at each cross-section, and the fluid as constant density.
For a car traveling 35 mph the distance required to brake for a stop is normally distributed with mean of 55 feet and standar deviation of 8 feet. You are traveling 35 mph in a residential area and a car moves abrupt into your path at a distance o..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd