Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
a) describes the impact of non--ideal op amp characteristics on the output of the inverting amplifier circuit. Assume that Rs = 10k and Rf = 1 M. Let A = 105, Ri = 2 M, R0 = 75 . If these nominal non--ideal parameters are replaced, one at a time, by A = 50000, Ri = 1 M and R0 = 150 (each of which is twice as bad as the nominal values), which parameter has the largest impact on the output voltage? In other words, the output voltage is most sensitive to the variation of which non--ideal parameter?
b) Compare the above results with the possibility that Rf is chosen to an accuracy of 1%. Which has a bigger impact on the output voltage?
A serial input finite state machine has one input and one output. The output becomes 1 and remains 1 thereafter when at least two 0's and at least two 1's have occurred as inputs, regardless of the order of occurrence. Draw a state diagram for the..
computation with 5% of the code that cannot be paralleled, compute the speedup and efficiency.
Suppose that without a 1k-ohm load an amplifier's output voltage is 5Vpp but when the 1k-ohm load is attached, it drops to 3Vpp. What is the output impedance of the amplifier
1. What is the step response equation for charge time 2. How to determine the current in RLC circuit using the osciscope 3. List three reseasons why the measured value and pspice value for tau are different.
An automobile battery has an open-circuit voltage of 13.6 V and a total internal resistance of 0.012 ohms. What is the terminal voltage of the cell when it is delivering 250 A to the starter motor
The total charge that has accumulated on the positive plate of a capacitor varies with time. The charge follows q=At^2 for the first 4s. a) Find the value of current at t=2,6,9,12,16 s. b) Sketch the current i(t) as a function of time
A 10 kwatt, 480V , single phase 60Hz, 24 pole motor has an stator winding resistance of 0.1 ohm from line-to-neutral. The rotor is not a permanent magnet but a separately powered electromagnet (field wind-ings) that takes .5 A at 120 V.
Design a sequencer with an enabler with 3 outputs that when enabled follows a successive clock sequence of 000,000,011,011,110,110,010,011 when the last step is reached the sequence returns to the beginning.
Design a counter to count even numbers between 0 and 15. Therefore states will be 0 -> 2 -> 4 -> 6 -> 8 -> 10 -> 12 -> 14 -> 0. If any unused state is encountered bewteen 0 and 7, then the counter should go back to initial state 0.
how to calculate theoretical range when measuring resistance with DMM (amprobe-AM530) how to adjust the tektronics TBS1104 oscilloscope Time/div to a value of 0.5ms the tektronics only let me adjust between o and 1 ms, but nothing in between.
Determine the dynamic behavior of the tank concentrations (CA0 and CA) in response to a step change in inlet concentration by 0.925 mole/m3. Estimate the time it takes until 63% of the change in outlet concentration, CA has occurred.
3) What factors started the decline in the nuclear power industry, and what events essentially ended new construction of nuclear power plants 4) What are three advantages of using AC power over using DC power
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd