Reference no: EM131090706
Directions: Be a detective and deduce the type of material of each specimen!
Measure the geometry and masses of 4 tensile samples. Perform tensile tests on the samples and collect force (N) vs. displacement (mm) data and convert toengineering stress (MPa) vs. strain plots. Determine the mechanical properties of each and compare your results to theoretical values using VMSE, Appendix H, and literature/web resources (e.g. www.matweb.com, www.azom.com).
Sample Geometry:
|
sample
|
Reduced area length (L0, cm)
|
w (cm)
|
t (cm)
|
x-sect.
Area (A0, m2)
|
Approx.
total volume
|
Mass (g)&
Weight (N)
|
Density ρ (g/cm3 orkg/m3)
|
Notes on appearance
|
|
1
|
|
|
|
|
|
|
|
|
|
2
|
|
|
|
|
|
|
|
|
|
3
|
|
|
|
|
|
|
|
|
|
4
|
|
|
|
|
|
|
|
|
Stress-strain Properties:
|
sample
|
E (GPa)
|
σy(0.002 offset, MPa)
|
εy
|
σuts
(MPa)
|
σf
(MPa)
|
εf
|
Strength/weight ratio
|
Notes during test/fracture
|
|
1
|
|
|
|
|
|
|
|
|
|
2
|
|
|
|
|
|
|
|
|
|
3
|
|
|
|
|
|
|
|
|
|
4
|
|
|
|
|
|
|
|
|
Questions:
1) From the plots, determine properties of each sample in the tables above. Which material was the most stiff? Which was the most flexible?
2) Compare the samples in order from highest to lowest values obtained for: σy, σuts, and strength-to-weight-ratio (σuts/(ρ*9.81)) for each of the 4 samples. Give an example of when each of these 3 different strength properties might be preferred.
3) Based on the stress-strain curve, which material is most ductile? Which is most brittle?
4) Describe the fracture surface and fracture behavior of each material and what this conveys about the material (necking?shape/angle of fracture?).
5) Compare the mechanical and physical properties to literature and deduce the material (for additional points, name the alloy or specific grade for the metals).YOU MUST JUSTIFY YOUR RESPONSE!!!! (i.e. what properties matched with literature and led you to your conclusion)
Bonus: Comment on any major sources of error or uncertainty in this exercise. Be specific about how the results will be affected by any uncertainty.
|
Discovery and incident management
: Determine which of the seven recommendations to improve e-Discovery and incident management you would consider the most important for organizations to address. Justify your answer.
|
|
Solve this kind of question
: How to solve this kind of question? When will the insertion be unsuccessful?
|
|
Describe the diverse cultures and language patterns
: Explain, in a clear organized paragraph with at least eight sentences, the irony of that ending phrase - Describe the diverse cultures and language patterns
|
|
Name of the system that system d replaces
: 1. What does the d in system d stand for in Linux? 2. What is the name of the system that system d replaces (the older name)? 3. What is a service unit when referencing systemd?
|
|
Which material was the most stiff
: Compare the mechanical and physical properties to literature and deduce the material (for additional points, name the alloy or specific grade for the metals).YOU MUST JUSTIFY YOUR RESPONSE!!!! (i.e. what properties matched with literature and led..
|
|
You use to investigate the scenario
: For this assignment, you will use the case study you selected for your Week 1 assignment. Write a 260- to 350-word paper that explains the following about your chosen case study:
|
|
What should your microcomputer do when the fifo is full
: The objective of this exercise is to design a microcomputer-based IEEE488 to RS422 simplex converter (Figure 14.23).
|
|
Find the value of the test statistic
: Find the value of the test statistic - Find the critical value(s) and state the decision about the null hypothesis and Determine whether the samples are independent or dependent.
|
|
Two bible commentaries or religion-centered websites
: Must use at least one or two Bible commentaries or religion-centered websites as well. At the end of your essay you should briefly list the sources that you used, i.e. Arnold and Beyer, Encountering the Old Testament, name/link/date of website, et..
|