Which component will have the higher partial pressure

Assignment Help Civil Engineering
Reference no: EM131034207

In a gas mixture, which component will have the higher partial pressure-the one with the higher mole number or the one with the larger molar mass?

Reference no: EM131034207

Questions Cloud

Solicited proposal to build a small shopping center : If you were submitting a solicited proposal to build a small shopping center, would you include as references the names and addresses of other clients for whom you recently built similar facilities? Where in the proposal would you include these refer..
Pepare a strategic analysis and recommendation : Pepare a strategic analysis and recommendation for a given company (Panera).  For this project, all teams in the class will be assigned the same company to examine with respect to its current, real-world strategic situation.  A significant portion of..
How is the p-v-t behavior of a component in an ideal-gas : How is the P-v-T behavior of a component in an ideal-gas mixture expressed? How is the P-v-T behavior of a component in a real-gas mixture expressed?
Abrogation of the academics duty : Do you think that this represents an abrogation of the academics duty to serve the community that supports them - reports generated in accordance with accounting standards?
Which component will have the higher partial pressure : In a gas mixture, which component will have the higher partial pressure-the one with the higher mole number or the one with the larger molar mass?
How derivative products enhances the efficiency : Discuss how derivative products enhances the efficiency of the financial market in the respective countries. (Please note that your discussion should take into consideration of implication of at least one of the country's specific factor)
Determine the compressibility chart and amagat''s law : A volume of 0.3 m3 of O2 at 200 K and 8 MPa is mixed with 0.5 m3 of N2 at the same temperature and pressure, forming a mixture at 200 K and 8 MPa.
Determine the mass fraction and partial pressure of each gas : A gas mixture at 350 K and 300 kPa has the following volumetric analysis: 65 percent N2, 20 percent O2, and 15 percent CO2. Determine the mass fraction and partial pressure of each gas.
Give the editorial a catchy title and state your position : A letter to the editor is a briefly stated opinion generally written in response to a current issue or previously published article. It is typically very short-250-300 words. The purpose is to raise awareness of an issue, persuade people to thin..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Do the first three time increments by hand

A variable-order reaction A-->B has the following rate expression: R(a) = -kC(a)/(K+C(a)) where k = 5mg/L-hr and K=40mg/L The reaction is to take place in a batch reactor. The initial concentration is 450 mg/L

  Determine bod reaction rate constant of municipal wastewater

If the BOD5 of a municipal wastewater is 310 mg/L and the BOD U is 340 mg/L, determine the BOD reaction rate constant (base e). What would be the 3 day 30°C BOD Assume, temperature coefficient = 1.047.

  Determine themax value of bending stress in the beam

A beam of rectangular cross section 300mm by 100mm sitsupright and has a moment of inertia of 225 X 10-6m4 and a max bending moment of 67.5KNm. Determine themax value of bending stress in the beam.

  Calculate the force acting on a window facing the storm

the wind reaches a speed of 27.8 m/s in a storm. calculate the force acting on a 1m x 2m window facing the storm. the window is in a high-rise building. the air density p= 1.2 kg/m3.

  Find the maximum area that the rancher can enclose

A rancher has 1200 ft of fencing to enclose a double paddock with two rectangular regions of equal areas. find the maximum area that the rancher can enclose.

  Find dimensions of channel for least expenditure of energy

A trapezoidal channel having side slopes of 2 horizontal and 1 vertical discharges 14.35 m3/s of water at a velocity of 1.0m/s. The channel lining has a roughness coefficient, n = 0.013. Find the dimensions of the channel for the least expenditure..

  Determine the volume flow rate

Water with a static pressure of 1.96kN/M2 flows through an 800 mm diameter pipe. A pitot tube pressure gage in this pipe reads a pressure of 5.88 kN/M2. How do you determine the volume flow rate (Q) of the water? (Q = 1.40 M^3/sec, V=2.79 M/sec)

  Explain the working principles of two tests that can

Should the soil be compacted at the dry of optimum or at the wet of optimum condition in order to minimize the swelling potential? Briefly explain the reason for your answer.

  What distance will the concentration of the metals be

Another way to treat acid mine drainage is to add limestone at the beginning of a narrow AMD stream to precipitate the metals. The first order rate constant is 10/day. Assume the stream is 3ft wide and 1ft deep

  Classify the soils using the given grain size distribution

Classify the following soils using the given grain size distribution (ASTM system) and Atterberg Limits data:

  Calculate the maximum bending stress on each side

A square steel bar, 38 mm on each side, is used as a beam and subjected to bending of 460 N.m. Calculate the maximum bending stress.

  What is the arc distance of one second of longitude and one

Given a mean earth radius of 20,906,000 ft, and an observation latitude of N 33 degrees, what is the arc distance of one second of longitude and one second of latitude?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd