Where the maximum ground level concentration would occur

Assignment Help Civil Engineering
Reference no: EM13296832

Air Dispersion Model
a power plant burns 150,000 tonnes (1 tonne = 1,000 kg) of coal each year. The coal has 2.5% sulfur content, and the air pollution control equipment removals approximately 94% of sulfur. Assume 10% of the sulfur content ends up in the ash. The remaining combustion products are discharged through an 80 m stack with a diameter of 3.0 m. The stack off gas temperature and velocity are 320 oC and 4 m/s, respectively, and the atmospheric conditions are 102 kPa and 25 oC. If the atmospheric conditions are slightly unstable (Class C) and the wind velocity at 10 m elevation is 3.5 m/s:

1. Plot the ground level concentration of sulfur dioxide as a function of distance from the stack and determine the maximum ground level concentration at both with and without air pollution control and the distance from the stack where the maximum concentration occurs.

2. With air pollution control equipment in place, plot the contours for a ground level concentration that is half and ¼ of the maximum value and indicate on your plot the location of the stack and the location of the point where the maximum ground level concentration would occur.

3. Compare your result with Ambient Air Quality Standard and comment it.
Note:
Sulfur dioxide:
Ambient Air Quality Standard = 0.03 ppm at annual average (80 µg/m3 or 8 x 10-5 g/m3 )
Lethal concentration: 400-500 ppm (0.11-0.14 g/m3 )

Reference no: EM13296832

Questions Cloud

Why is not it cost-effective to underinsure your property : What improvements can you make to an existing home to take advantage of premium reduction programs? 3. Why is not it cost-effective to underinsure your property?
Explain the equation for the combustion of gaseous methanol : The equation for the combustion of gaseous methanol is: 2CH3OH(g) + 3O2(g) ? 2CO2(g) + 4H2O(g) Estimate the ?H°rxn per mole of methanol combusted, using the bond energy data provided below
What is the contribution margin per procedure and break-even : what is the contribution margin per procedure and break-even point?
Find an algebraic epxression for your weight : Someone's weight while standing on the Earth's surface is m x g, where g has the familiar surface value of 9.80 m/s^2. Find an algebraic epxression for your weight
Where the maximum ground level concentration would occur : a power plant burns 150,000 tonnes (1 tonne = 1,000 kg) of coal each year. The coal has 2.5% sulfur content, and the air pollution control equipment removals approximately 94% of sulfur. Assume 10% of the sulfur content ends up in the ash.
Briefly describe your agencys services and setting : Present a conflict situation from your own human service work that involves any number of parties, including yourself (you must be a part of the conflict/dilemma), the client, the family, the agency, the board, the funding agency, etc.
Explain what happens when the calorimeter cup : what happens when the calorimeter cup has several milliliters of water in it when you added in the HCl
Describe what is the partial pressure of the o2 : A sample of oxygen is collected over water at a total pressure of 616.8 mmHg at 30 deg Celsius. the vapor pressure of water at 30 deg celsius is 31.8 mmHg. What is the partial pressure of the O2
Find si value of absolute pressure corresponding to vaccum : What is the SI value of absolute pressure corresponding to a vacuum pressure of -10 inches of water. Assume the location is Moscow, Idaho. What is the SI value of gage pressure corresponding to a pressure 14 psia. Assume the location is Denver, Colo..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the required diameter of steel tie rods

CALCULATE THE REQUIRED DIAMETER OF STEEL TIE RODS NECESSARY TO SUPPORT A BALCONY. EACH ROD, SUSPENDED FROM A ROOF TRUSS, SUPPORTS A FLOOR AREA OF 7.0m^2. THE COMBINED BALCONT FLOOR LOAD IS 10.5 kPa

  Determine the cycle time for a single engine scraper

Determine the cycle time for a single engine scraper rated at 21 cy heaped that is used to haul material from a pit to a fill 900 ft away under severe conditions. The average haul speed will be 14 mph and the average return speed will be 20 mph.

  Constant head permeability test

A constant head permeability test was conducted on a clean sand sample. The diameter and length of the test specimen were 10 cm and 12 cm respectively.

  Inability and green engineering can be integrated

inability and green engineering can be integrated in the four components of materials science and engineering?

  Design the ramp for the highest horizontal curve

The entrance to Mt. Hood Meadows (elevation 3,075 ft at the point of crossing) is grade separated from Viking highway (elevation 3,050 ft at the point of crossing) and will have to be connected. The two roadways intersect at a right angle.

  To what maximum angle, measured from vertical

To what maximum angle, measured from vertical, does the rod (with the attached ball of clay) rotate?

  What should actually the separation distance

At what speed the rule of 25 feet separation between two cars is safe?

  Determine what is the speed in rpm of the car wheels

If a car engine is turning at 4000 rpm, the transmission gear ratio is 3:1 and the final drive ratio is 4:1. (a) what is the speed in rpm of the car wheels and (b) the vehicle speed if the tire radius is 8 inches

  Four-lane urban freeway

A four-lane urban freeway (two lanes in each direction) is located on rolling terrain and has 12-ft lanes, no lateral obstructions within 6 ft of the pavement edges, and an interchange every 2 miles.

  Determine the overturning moment of silt and water

Assuming that silt is equivalent to a liquid having a density of 1760 kg/m3, determine the overturning moment of silt and water about point A.

  Calculate the force

Calculate the force (in Kn) a punch press must exert if it is to punch out a large washer from a strip of 5-mm thick sheet steel with an ultimate shear strength of 400 MPa. The washer dimensions are as follows: hole diameter is 27 mm. outside diam..

  Problem on coefficient of rolling resistance

What is the minimum distance from the stalled car at which the driver could apply the brakes and still stop before hitting it? Assume coefficient of rolling resistance of 0.013.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd