Where is the insulation temperature greatest

Assignment Help Mechanical Engineering
Reference no: EM131394263

Question 1).

A 1/8" diameter copper wire is covered with 1/16" thick insulation (k = 0.21 Btu/hr-ft- oF). Air blows in crossflow over the wire at 19 ft/s. The wire carries a current of 300 A and the air is at 80oF. The electrical resistivity of copper is 6.77 x 10-7?-in. Where is the insulationtemperature greatest? Determine this temperature. (NOTE: You will need to use a thermalresistance network to represent the heat transfer through the insulation into the surrounding air.)

Question 2)

The walls of a house are constructed of an exterior sheathing, insulation, framingtimber, and drywall. The composite resistance of the materials is 4.15 m2-K/W. On a winter daywhen the outdoor temperature is -5oC, wind blows at 30 km/hr parallel to the 3 m high, 18 m longwall. If the convection coefficient on the interior side of the wall is 5 W/m2-K and the interiortemperature is 21oC, determine the rate of heat loss through the wall

Reference no: EM131394263

Questions Cloud

Find the mass moment of inertia about the x axis : The object shown is made of thin plate with 0.02 lb/in2 specific weight. Determine the mass moment of inertia about the x axis.
Write a report on the annual patterns : Which month has the smallest range?- Write a brief comparison of the ozone levels in January and June.- Write a report on the annual patterns you see in the ozone levels.
Explores professional ethics and responsibilities : Create a 5- to 6-slide PowerPoint presentation that explores professional ethics and responsibilities. You can use information from reliable sources.
Write a few sentences describing given wine prices : Which lake region produces the cheapest wine?- In which region are the wines generally more expensive?- Write a few sentences describing these wine prices.
Where is the insulation temperature greatest : If the convection coefficient on the interior side of the wall is 5 W/m2-K and the interiortemperature is 21oC, determine the rate of heat loss through the wall
Find the interior heattransfer coefficient : Find the interior heattransfer coefficient. Is heat transfer best on the interior or exterior surface of the stack? Explainyour answer.
Write a memo supporting one proposal over the other : BUS 300- Write a memo supporting one proposal over the other with the following in mind: The City Council wants to reduce traffic in the downtown/campus area.
Calculate the tension in the string : calculate the tension in the string and the magnitude of the horizontal forces
Summarize about fuel economies of given two types of vehicle : Combined Fuel Economy (using an average of driving conditions) in miles per gallon by whether the car has two- or four-wheel drive. Summarize what you see about the fuel economies of these two types of vehicles.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd