When a net amount of work is done on a closed

Assignment Help Civil Engineering
Reference no: EM13536837

t or f

a)a process that violates the second law of thermodynamics also violates the first law of thermodynamics.

b)when a net amount of work is done on a closed system undergoing an INTERNALLY REVERSIBLE process, a net heat transfer of energy from the system also occurs.

c)a closed system can experience an increase in entropy only when a net amount of entropy is transfered into the system.

d)the change in entropy of a closed system is the same for every process between two specified states.

Reference no: EM13536837

Questions Cloud

What is fc and d : 5 1/8 in thick laminated timber 24ft long column to support a roof 16 kips and floor load 38kips will be applied at 13' 4" from base.
Determine the minimum required wire diameter assuming : A large steel tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 19,000N. Determine the minimum required wire diameter assuming a factor of safety 5 and that the yield strength of the steel is 900M..
Determine the entrance losses : A 40 cm diameter well has been constructed in a water-table aquifer. A pump capable of continuous discharge at 600 m3/day has been installed to test the well. Observation wells are located 10 meter and 50 meters from the pumped well. After pumping co..
What is the coefficient of static friction : A chair weighing 150 rests on a level floor that is not frictionless. A man pushes on the chair with a force = 43.0 that is directed at an angle of 34.0 with the horizontal. Assume that the chair is stationary but is on the verge of sliding.
When a net amount of work is done on a closed : When a net amount of work is done on a closed system undergoing an INTERNALLY REVERSIBLE process, a net heat transfer of energy from the system also occurs.
What length of time in the model corresponds to one day : A 1:2000 scale tidal model is operated to satisfy Froude’s law. A velocity of 0.02 ft/s is observed in the model. What is the velocity at the corresponding point in the prototype? What length of time in the model corresponds to one day in the prototy..
Determine the rotation of the gear at e : The two shafts are made of A-36 steel. Each has a diameter of 25 mm and they are connected using the gears fixed to their ends. Their other ends are attached to fixed supports at A and B
What is the probability of a water shortage in this city : During the next month, the amount of water available for a city is lognormally distributed with a mean of 1 million gallons and a c.o.v. of 40%, where as the total demand is expected to follow a lognormal distribution with a mean of 1.5 million gallo..
Explain how these effects were initiated : Is it possible (in this part of the world) for the sun to ever shine directly upon the OUTSIDE of a NORTH-facing wall of a home or other building? If so when?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Define what stress will be necessary to the slip plane

Consider a metal single crystal oriented such that the normal to the slip plane and the slip direction are at angles of 42.1* and 48.9*, respectively, with the tensile axis.

  Solve the quadratic equation in as for requirement

Select the number and size of reinforcing bars required to resist a total factored moment of 180 ft. kips for a rectangular section with b = 12 in., d = 19.5 in., h = 24 in., fc = 4 ksi, and fy = 60 ksi. Check for minimum reinforcement requirement..

  1 a watershed contains 162 ha and 243 ha of agricultural

1. a watershed contains 16.2 ha and 24.3 ha of agricultural and residential land use respectively. the last rainfall

  Determine the maximum shear stress in the material

An element of aluminium in a form of a rectangular parallel pipe has a length 'a' along the x axis of 5.5 in, a length 'b' on the y axis of 4.5 in. Determine the maximum shear stress in the material,the change in length.

  Determine what would be better a truss with all 60 angles

what would be better a truss with all 60 angles or a truss with a 30 60 90 angle for a bridge design what would be the best design

  How many tons of water must be added to solids to achieve

Ten tons of a mixture of paper and other compostable materials has a moisture content of 7%. How many tons of water must be added to the solids to achieve a mixture with 50% moisture for composting

  How many days would wastewater take to fill the lagoon

a lagoon is 20 ft by 80 ft with a depth of 5.5 ft .Wastewater from households flow into the lagoon at 260 gal/day .How many days would it take to fill the lagoon

  List and describe each of the files that would be required

For a multi-file project that contains just one class, list and describe each of the files that would be required to implement and test the functions of the class.

  Calculate the work produced and heat rejected by the engine

A completely reversible heat engine uses a solar receiver for a hightemperature reservoir and a lake for a low temperature reservoir. The sun maintains the receiver surface at 290 ° F while the lake remains at 40 °F.

  Compute the required stirrup spacing at the given location

At a certain location along the span, a reinforce concrete beam section with d=14 in. and b=10 in. is subject to a design shear of Vu=50k. Using No.4 stirrups, compute the required stirrup spacing at the given location. assume F'c=3 ksi and Fy=40 ..

  Calculate total vertical stress and pore water pressure

if the density of the clay is equal to 2.0 Mg/m3 ,calculate the total vertical stress ,pore water pressure and effective vertical stress at a depth of 5 meters below ground level.

  What is the maximum height the pump can be installed

A particular mixed flow pump is operating just below the point of cavitation. The pump is sited with its intake 3 m above the water level in the reservoir and delivers 0.05 m3/s.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd