Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Problem 1: Consider the following Wheatstone bridge:
a) Solve R3
b) In the bridge circuit shown above, the bridge is nulled with R1 = 1000Ω, R4 = 421Ω, and R2 = 500Ω, Find the value of R3.
c) The resistor in the bridge shown above are given by R1 = R2 = R3 = 120Ω and R4 = 121 Ω.
If the supply voltage Vdc = 10.0 V, Find the voltage offset Vo.
Design a filter for a biomedical instrument to eliminate DC (f = 0), 500 Hz tone, and its corresponding harmonics. The system sampling rate is 2,000 Hz. Place all the required poles at the origin to obtain a FIR filter.
A1. An amplifier has cutoff frequencies of 120.0 Hz and 1.200 kHz. Calculate the bandwidth and center frequency of the amplifier. A2. The upper cutoff frequency of an amplifier is 8.000 MHz and its center frequency is 1 MHz.
A 450 kW motor operating 73% Power factor lagging is connected to a 120V(rms), 60Hz line. (a) Sketch and label the power triangle for the motor. (b) Find the rms current into the motor.
The triggering device for an automobile airbag restraint is required to have a reliabil-ity of 95 per cent when tested on an impact test rig. This reliability is to be established at 90 per cent confidence. The test is destructive.
Transmitting data at higher speeds generally requires a wider bandwidth, which is not always possible within FCC guidelines. In addition to the wider bandwidth, higher speed transmission also requires a higher transmit power. Why
Use Matlab to verify the central limit theorem for the sum of N independent exponential RVs (with a=0 and b=4) for N=5, 10 and 20. Repeat for the sum of N independent RayleighRVs (with a=0 and b=4). Comment on the fit to the approximate Gaussian pdf.
Determine the current in a circuit consisting of a 1000-ohm resistor with a voltage of 50 volts DC across it. When using an ammeter, why do you place it in parallel with the circuit
A 230 V DC series motor has an armature circuit resistance of 0.2 and a eld circuit resistance of 0.1. At rated voltage, the motor draws a line current of 40A and runs at a speed of 1000 rpm.
determine the displacement noise of the sensor with the electrodes at a position midway between maximum andminimum separation if the output signal is filtered to provide bandwidth of 10, 100, and 1000 Hz
Assume that a receiver has a first amplifier stage with a 5KW input resistance, a gain of 300, an input audio signal of 20 mV, and an operating temperature of 27oC. When the amplifier is operating with a bandwidth first of 10 MHz,
Design an 8-bit register with 2 control inputs s1 and s0, 8 data inputs I7..I0, and 8 data outputs Q7..Q0. s1s0=00 means maintain the present value, s1s0=01 means load, and s1s0=10 means clear. s1s0=11 means to swap
Given A=a1, a2, a3,a4 B=b1, b2, b3, b4 1) Design an adder using only multiplexers with one address bit.2) Design an adder using only multiplexers with two address bits.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd