What would the pressure rise to

Assignment Help Mechanical Engineering
Reference no: EM13216520

A storage tank holds 75 cubic meters of a gas at 28deg C and a pressure of 130kPa. The gas appears to have a molecular weight of 30 from tests run in a laboratory. Estimate the mass of the gas in the tank in kg assuming the gas behaves as an ideal gas. If the gas warms up to 35 deg C as it sits in the sun all day, what would the pressure rise to?

Reference no: EM13216520

Questions Cloud

What is the approximate ductility expressed as a percentage : Estimate the energy that must have been supplied to cause the specimen to reach failure.
Different incentive plans : Select three different incentive plans. You may select individual plans, group plans, or a combination. List the pros and cons for each plan.
Explain the difference between the two methods : Explain the difference between the two methods and which method is required by the Australian Accounting standards?
Determine the angular velocity : Determine the angular velocity of the two 10-kg rods in Fig. 2 when , if they are released from rest in the position . Neglect friction.
What would the pressure rise to : Estimate the mass of the gas in the tank in kg assuming the gas behaves as an ideal gas. If the gas warms up to 35 deg C as it sits in the sun all day, what would the pressure rise to?
Find the primary manner in which orion has increased : Discuss specific challenges that you may have experienced with any of the subject matter presented, and point out the areas for which you would like more information.
What is the mass flow rate of oxygen : What is the mass flow rate of oxygen in lbm/s? Note that the inside diameter of a nominal 2 inch schedule 40 steel pipe is 2.067inches. Assume ideal gas principles apply.
Connection between moral character and political activism : What is the connection between moral character and political activism? Do you think there should be a link between good moral character and political activity?
Estimate the mass of the gas in the tank in kg : Estimate the mass of the gas in the tank in kg assuming the gas behaves as an ideal gas. If the gas warms up to 35 deg C as it sits in the sun all day, what would the pressure rise to?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the acceleration of the cabinet

Determine the acceleration of the cabinet when sA = 40 ft. Note that when sB = 0, sA = 0 (points A and B are coincident).

  Determine a velocity using bernoullis equation

If I take measurements using a Pitot Tube and get results for pressures Horizontal In, Horizontal Out, Vertical In, and Vertical Out all in inches of mercury. How do I take these pressures and determine a Velocity using Bernoullis equation?

  Determine the expressions for the principal stresses

A circular shaft is subjected to a torque Ta and a bending moment Ma. Assuming that the diameter of the shaft is d, determine the expressions for the principal stresses and maximum shear stress in terms of Ma, Ta and d.

  Explain carbon content of steel

Carbon content of steel, A steel contains 55% alpha-ferrite and 45% gamma-ferrite or austenite at 750 degrees celcius. What is the carbon content of steel?

  Define- hydraulic mean radius

Define- hydraulic mean radius, hydraulic dept, section factor and most efficient dhannel cross section.

  Explain the temperature of the refrigerant

Find the Temperature of the Refrigerant, A closed vessel with a volume of 2 ft^3 contains 5 lb of Refrigerant 134a. A pressure sensor in the tank wall reads 71.39 lbf/in.^2 (gage).

  Determine the maximum allowable force p

a uniform rectangular cabinet having dimensions shown and mass m=50kg is placed onto a cart of mass 10 kg as shown. no slipping between cabinet and cart. determine the maximum allowable force P so that the cabinet does not tip.

  Determine the magnitudes of fa and fb

The total force Fa + Fb exerted on the shelter is in the direction parallel to the line L and it's magnitude is 400 lb. Graphically determine the magnitudes of Fa and Fb.

  Calculate the longitudinal engineering strain

A paper clip is made of wire 0.7 mm in diameter. If the original material from which the wire is made is a rod 25 mm in diameter, calculate the longitudinal engineering strain and true strain that the wire has undergone during processing.

  Find the velocity of the jet air

If the deflection of the gae fluid height, h, is 2 inches find the 1) velocity of the jet air and 2) the force exerted on the disk by the air.

  Why is the carnot cycle not suitable as an ideal cycle

why is the carnot cycle not suitable as an ideal cycle for all the power producing devices ?

  How does artificial aging affect kic in a 7075 alloy

How does artificial aging affect KIC in a 7075 alloy? Which is likely to have a higher KIC: 7075-T6 or 7075-T7? Explain.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd