What would the height be after it was consolidated into this

Assignment Help Civil Engineering
Reference no: EM13559238

There is a perfectly uniform soil that is an assemblage of spheres of equal diameter. A 1m thick layer of this soil is packed so that it is as loose as possible (void ratio, e_max ~= 0.9), and then it was vibrated until it was as dense as possible (void ratio, e_min ~= 0.35). What would the height be after it was consolidated into this dense packing? Detailed explanation please

Reference no: EM13559238

Questions Cloud

Determine poissons ratio and the new length : The aluminum block has a rectangular cross section and is subjected to an axial compressive force of 8kip. If the 1.5-in side changed its length to 1.500132 in., Determine Poisson's ratio and the new length of the 2-in side. E = 10(10^3)ksi
Design a hollow steel shaft with an inside diameter : Design a hollow steel shaft with an inside diameter 1/3 that of the outside diameter. The shaft transmits 200 kW at a speed of 20 Hz. The allowable shearing stress is 55 MPa, and the allowable angle of twist is 1 degree per meter of length.
Estimate the capacity of the existing system : You meet with a potential client to discuss a land development project. Your client wants to know the capacity (in cfs) of the existing water supply system serving the area With a 450-ft pipeline
Find how many protons are absorbed by the tumor : A cancer patient is undergoingradiation therapy in which protons with an energy of 1.2 MeV areincident on a 0.25 kg tumor. How many protons are absorbed by the tumor
What would the height be after it was consolidated into this : There is a perfectly uniform soil that is an assemblage of spheres of equal diameter. A 1m thick layer of this soil is packed so that it is as loose as possible (void ratio, e_max ~= 0.9),
Calculate total co2 emissions from two polices : Two changes to the CAFE standard for US automobiles are being considered. A more conservative increase from 27.5 mpg in 2011 to 35 mpg by 2020 is supported widely in Washington. California and 13 other states + the District of Columbia hope to increa..
How much of a reduction in the automobile emission rate : How much of a reduction in the automobile emission rate would be required to achieve the maximum eight-hour average NAAQS for CO at steady state 9 ppmv ( (10.3 mg/m^3)?
Obtain from what height above ground was the marble thrown : A marble is thrown horizontally with a speed of 13 m/s from the top of a building. From what height above the ground was the marble thrown
What is the fuel consumption under these conditions : First consider highway driving. Assume a constant velocity of 27 m/s (60.4 mph) on level ground. Under these conditions the efficiency of the engine plus auxiliaries is 30 percent and the efficiency of the drivetrain is 85 percent. What is the fuel c..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Design the weir structure in order to accommodate the design

To avoid submergence the crest of the weir must be at least 0.05 m above the downstream water depth. Here we can assume that the depth downstream is equal to the normal depth. To simplify calculations we will assume that Cd = 0.7 Water depth over the..

  Which of materials listed in table are possible candidates

A cylindrical rod with a length of 380 mm and a diameter of 10 mm is to be subjected to a tensile load. The rod must not experience plastic deformation or an increase in length of more than 0.9 mm when a load of 24.5 kN is applied.

  Determine magnitude of tension t and x-y-z components

If the pulleys are fixed to the shaft, determine the magnitude of the tension T and the x,y,z componenet sof reaction at the smooth thrust bearing A and smooth journal bearing B.

  How much benzene they can release into river

A company near City X want's to know how much benzene they can release into River Y. City Z is 85.5 miles downstream from City X. City Z doesn't want to have Benzene levels higher than 0.0000015 g/L.

  At what temperature change delta t does the wire go slack

a brass wire of diameter d=1/6 in is stretched between rigid supports with an initial tension T of 37lb. assume the coefficient of thermal expansion is 10.6X10^-6 / F and the modulus of elasticity is 15X10^6 psi.

  Determine the control efficiency needed to meet the criteria

A Chemical manufacturer emits air with 250 PPM of toluene at 1 atm and 30 degrees C at a flow rate of 10,000 cubic meters per minute.The air is routed to a biofilter to control total emissions to less than 110 kg/day of toluene.

  Compute the bearings for great plain avenue

Compute the bearings for Great Plain Avenue and Colby Street), polylines, blocks for the direction arrows and the "H's" in the parking area.

  What is the average chear stress in the glue joint between

Two 1/2 inch rods are spliced together by glueing a 2 inch section of plastic pipe over the rods ends. If a tensile force P = 350 lb is applied to the spliced nylon rod, what is the average chear stress in the glue joint between pipe and the rods?

  Determining specific gravity

The cross sectional dimensions of a 4-ft-long wood member at 30% moisture content is 1.5 in. x 7.5 in., and its weight is 11 lb. At oven-dry condition, its dimensions and weight are 1.35 in x 6.8 in., and 10.2, respectively. What is its specific g..

  Determine hydraulic retention time in the treatment system

The BOD5 of the influent wastewater is 150 mg/L and the first-order reaction rate for the degradation of BOD5 is 0.6/hr at 20°C. If the required effluent BOD5 is 20mg/L

  Determine the velocities and u and v and the speed of the

Determine the velocities and u and v and the speed of the flow along the streamline at (3,2). Determine the slope of the streamline in degrees from horizontal. Determine the acceleration at the point. Determine the pressure at the point (3,2) in N/m2..

  Explain the rule to solve the moment through the reactions

When using singularity functions, if I have a reactionary moment at a cantilever connection, do I use the right hand rule to solve the moment and determine it's direction through the reactions

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd