User Account

All Pages

What would be the retention time in each tank

Assignment Help Civil Engineering
Reference no: EM13559313

A water treatment plant has 6 settling tanks that operate in parallel (the flow gets split into six equal flow streams), and each tank has a volume of 600 m3. If the flow to the plant is 10 MGD, what is the retention time in each of the settling tanks? If, instead, the tanks operated in series (the entire flow goes first through one tank, then the second, and so on), what would be the retention time in each tank?

Reference no: EM13559313

Questions Cloud

A polystyrene rod consisting of two cylindrical portions : A polystyrene rod consisting of two cylindrical portions AB and BC is restrained at both ends and supports two 6-kip loads as shown. Knowing that E = 0.45 X 106 psi, determine (a) the reactions at A and C, (b) the normal stress in each portion of the..
Find by how many degrees must the temperature be lowered : A cylindrical brass rod (cross-sectional area = 1.3 x10-5 m2) hangs vertically straight down froma ceiling. By how many degrees must the temperature be lowered
Estimate the heat added to the gas : A cylinder with a moveable piston holds 2.71 mol ofargon at a constant temperature of 307 K. Calculate the heat added to the gas
What is the maximum speed attained : The combined weight of a bicycle and its rider is 190 lbs, and when the rider is on the bike, their frontal area is 5.4 square feet, with a drag coefficient of 1.2. The coefficient of rolling resistance can be taken to be a constant for all speeds
What would be the retention time in each tank : A water treatment plant has 6 settling tanks that operate in parallel (the flow gets split into six equal flow streams), and each tank has a volume of 600 m3. If the flow to the plant is 10 MGD, what is the retention time
Find the support movements draw sfd and bmd : A fixed beam of span 6m carries point loads 20kN and 15kN at 2 m and 4 m from the left end respectively. Find the support movements draw SFD and BMD
Evaluate what is the frequency heard by the observer : A train at rest emits a sound at a frequency of 1000 Hz. What is the frequency heard by the observer
Evaluate the work done by the aluminum : A 3.0 kg block of aluminum isheated from 20°C to 90°C at atmospheric pressure. Find the work done by the aluminum
Calculate the concentration of pm in the stack : A stack (T=550*F and P=750mm Hg) was sampled using EPA Method 5. The total gas volume that flowed through the dry gas meter was 2.785 cubic meters (at T=60*F and P=800mm Hg). The mass of particles collected was 1.50g. Also, 72.0g of H2O was collected..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the the oritical oxygen demand of a solution

Calculate the the oritical oxygen demand (mg/L) of a solution containing 450 mg of glucose(C6H12O6) in 2 liters of distilled water.

  How to compute the elevation of the target station

THE VERTICAL ANGLES WERE READ AT BOTH ENDS OF THELINE AND THEN AVERAGED USING A CO-AXIAL THEODOLITE/EDM COMBINATION.IF THE ELEVATION OF THE INSTRUMENT STATION IS 630.15 FT

  What is the pressure in the head of the flowing water

A combined pitot static tube has a coefficient of 0.98. Thedifferential head reading is 0.874m of water when it is positionedon the centreline of a pipe of constant diameter.

  What would be the concentration of pollutant in the

A lagoon with volume 1500 mg/m3 has been receivingsteady flow of non-conservative waste (reaction rake k = 0.20/day)at a rate of 125 m3/day for a long enough time to assume that steady- state conditions apply. The wasteentering the lagoon has a conce..

  Compute the effective normal stress acting on a plane

The water table is at a depth of 1 m. Compute the effective normal stress and the shear stress acting on a plane rotated 60 degrees clockwise from the horizontal at a depth of 2.5 m in this deposit.

  Determine the magnitude of the reaction force exerted at b

When the engine of the plane is running, the vertical reaction that the ground exerts on the wheel at A is measured as 616lb . When the engine is turned off, however, the vertical reactions at A and B are 520lb each.

  Find channel cross section and the required channel slope

A rectangular channel is to carry 200 cfs. The mean velocity must be greater than 2.5 fps. The channel bottom width should be about twice the channel depth. Find the channel cross section and the required channel slope.

  Calculate area of piece of property bounded by traverse arc

A (1275.11, 1356.11), B (1000.27,1365.70),C (1000.00, 1000.00),D (1450.00, 1000.00) with a circular arc of radius CD starting at D and ending at A with the curve outside the course AD.

  At what temperature does the liquid solidify

What is the composition of this last remaining liquid phase?

  Determine the pressure that develops in the container

A rigid-walled cubical container is completely filled with water at 40 0F and sealed. The water is then heated to 100 0F. Determine the pressure that develops in the container when the water reaches this higher temperature

  Determine the horizontal reaction

Determine the horizontal reaction that is developed on the gate at C.

  What are the spcs83 coordinates and convergence angle

What are the SPCS83 coordinates and convergence angle for a station in the Colorado Central zone with geodetic coordinates of 39° 44’ 40.74141”N, 105° 00’ 07.48466”W

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd