What would be the concentration of so2 in the stack gas if

Assignment Help Mechanical Engineering
Reference no: EM13644512

1-Approximately 130,000 tons (118 @106 kg) of coal are burned each year at the Iowa State University Power Plant. The coal is barged up from Kentucky to Davenport and trucked to Ames. Kentucky coal typically has a 2% sulfur content. What would be the average daily output (in kg/d) of sulfur dioxide (SO2) assuming that 4% of the sulfur content of the coal ends up in the ash (i.e. 4% of S is unreacted) and the rest is released in the stack gas?

2-As a rough approximation, the average oxygen content of dry air is about 21% by volume. If 20% excess air is used in the combustion process, how much air will be required each day?

3- What would be the concentration of SO2 in the stack gas if no pollution control equipment is used? Calculate your result on both a mass (g/m3) and volume (ppm) basis.

Reference no: EM13644512

Questions Cloud

A parallel-plate capacitor is formed from two 10 cm times : a parallel-plate capacitor is formed from two 1.0 cm times 1.0 cm electrodes spaced 2.9 mm apart. the electric field
You need a capacitance of 40 microf but you dont happen to : you need a capacitance of 40 microf but you dont happen to have a 40 microf capacitor. you do have a 56 microf
The liquid in the manometer has specific gravity of 08 find : a u-tube manometer is connected to a gas pipe. the level of the liquid in the manometer arm open to the atmosphere is
A 170 k resistor and a capacitor are connected in series : a 17.0 k resistor and a capacitor are connected in series and then a 18.0 v potential difference is suddenly applied
What would be the concentration of so2 in the stack gas if : 1-approximately 130000 tons 118 106 kg of coal are burned each year at the iowa state university power plant. the coal
A window washer is standing on a scaffold supported by a : a window washer is standing on a scaffold supported by a vertical rope at each end. the scaffold weighs 200 n and is
The object is attached to the rope at a horizontal position : an object of mass m 6.64kg is attached to a rope of negligible mass that is strung between two tops of two vertical
Using the appropriate form of the heat equation derive an : consider a one-dimensional plane wall with constant properties and uniform internal generation qdot. the left face is
If an additional 50 mj of energy are supplied to the : a 1.2-kg 10-cm-diameter solid sphere is rotating about its diameter at 69 revmin.a what is its kinetic energy?b if an

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd