What will temperature rise of lead be if there is no cooling

Assignment Help Civil Engineering
Reference no: EM13304697

Lead is extruded through a horizontal die under a pressure difference of 154.45 MN/m^2. What will the temperature rise of the lead be if there is no cooling while passing through the die? Assume lead to be incompressible and to have a density of 11360 kg/m^3 and a specific heat capacity of 130 J/kg K. Consider the steady-flow energy equation applied to the given extrusion process. Since the die is horizontal then there will be no change in potential energy from inlet to outlet. Hence the potential energy terms can be neglected. The velocity is also low in which case any change in kinetic energy which occurs will be small enough to be sensibly neglected. There is no cooling and also no external work done in which case these terms can also be neglected.

Reference no: EM13304697

Questions Cloud

What is the cost of equity for green using the dividend : The expected risk-free rate of interest is 2%, and the expected market premium is 5.5%. The company's beta is 1.2.
Find the velocity of the air downstream of the restriction : Find the velocity of the air downstream of the restriction, and show that the enthalpy is essentially the same before and after the throttling process. Also find the change of entropy.
Advise brain of the tax consequences arising from the sale : Advise George in each of the above situations as to his tax liabilities. Also advise him as to whether his receipts are income or capital on general principles.
What interest rate per six months was earned by the company : On January 1, 2005, this bond was sold for 110,000 dollars. What interest rate per six months was earned by the company on the BMI bond?
What will temperature rise of lead be if there is no cooling : Consider the steady-flow energy equation applied to the given extrusion process. Since the die is horizontal then there will be no change in potential energy from inlet to outlet. Hence the potential energy terms can be neglected.
What is the beta of this project : The firm owns this money. The market portfolio generates the payoff (200, 250, 300) and has an expected return of 8%. The risk free rate is 3%. Suppose CAPM holds.
What is the ground state energy of the electron : Take element Z = 21 from the periodic table. Ionize it 20 times so that there is only one electron left orbiting around the nucleus. What is the ground state energy of the electron
Find the magnitude of r dot and theta double dot at t : If r = (theta)2 and theta = 2t, find the magnitude of r dot and theta double dot when t = 2 s
Compute the angle between the axes of the polarizers : Unpolarized light with an intensity of 980 W / m2 is incident on a polarizer with an unknown axis. What is the angle between the axes of the polarizers

Reviews

Write a Review

Civil Engineering Questions & Answers

  Estimate energy release rate by using regression equation

A concrete building has floor area 10 m by 20 m and is 4 m high. THe building has four windows with a height 1.6 m and a width 2 m. After 10 minutes gases in the room have an average temperature of 700 degree Celcius.

  Find bod reaction rate constant of a municipal waste water

If the BOD5 of a municipal wastewater is 310 mg/L and the BODU is 340 mg/L, determine the BOD reaction rate constant (base e). What would be the 3 day 30°C BOD Assume, temperature coefficient = 1.047.

  Determine the average shear stress on the bolt surfaces

The top and bottom pull to the left with 10 kips each, the middle part 20 kips to the right. The bolts have a diameter 3/8 inch, determine the average shear stress on the bolt surfaces that are subjected to direct shear.

  Determine the torsional moment in the hollow x-section

A concrete box girder bridge has the rectangular x-section. The box is prismatic and considered thin-walled. It span is L=48m and simply supported at points A,B,C and D. The supports are assume to be able to transfer tensile forces.

  What are the total heads given by piezometers b and c

The total heads given by piezometers A and D are 98.9 cm and 3.6 cm, respectively. What are the total heads given by piezometers B and C?

  Determine the required width a of the plate

A steel plate 5/16" thick is embedded in a horizontal concrete slab and is used to anchor a high-strength cable as shown. The diameter of the hole in the plate is 3/4", the ultimate strength of the steel used is 36 ksi

  Municipal utility-considering two large-scale conduits

A big municipal utility district is considering two large-scale conduits. The first includes construction of a steel pipeline at a cost of $200 million.

  How to solve for the deficit concentration as function of x

Develop the mass balance equation and solve for the deficit concentration as a function of x, u, Lo, Do, ka, kd,and ks in the stream. Lo ans Do are the initial concentrations of BOD and DO deficit in the stream at x

  Determine maximum concentration of chlorides to be observed

A non-reactive chloride solution is continuously discharged into an aquifer. The concentration at the discharge location is 800 mg/L. Determine the maximum concentration of chlorides to be observed at an observation well 30 m downstream of the disc..

  Angular acceleration of the spool

determine the angular acceleration of the spool and the acceleration of the trailer. The wheels have negligible mass and are free to rotate.

  Determine the pressure within the tank using psf as unit

A water-filled U-tube manometer is used to measure the pressure inside a tank that contains air. The water level in the U-tube on the side that connects to the tank is 5 ft above the base of the tank.

  What is the percent change in its cross sectional area

The outside and inside diameters of 75 mm and 63 mm, respectively. A strain gauge is placed on the outside of the hollow segment of the tube to measure normal strains in the longitudinal direction. assume E=73 GPa and Poissons ration v=0.33. strai..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd