What will be the surface tension effects if the tube were

Assignment Help Civil Engineering
Reference no: EM13562630

1.A water column in a glass tube is used to measure the pressure in a glass pipe. The tube is 1/4 in. in diameter how much of the water column is due to the surface tention effects? What will be the surface tension effects if the tube were 1/8 in. or 1/32 in. in diameter?

2.

Reference no: EM13562630

Questions Cloud

Find the vertical reactions and construct the complete shear : A 16-ft [4.88 m] span beam is fixed at one end and simply supported at the other end. A single concentrated load of 9600 lb [42.7 kN] is placed at the center of the span. Find the vertical reactions and construct the complete shear and moment diagram..
What volume of ambient air was compressed : When the ambient air is at 70 degrees Fahreneit, 14.7 psia, and contains 21% oxygen by volume, 4.5 lb of air are pumped into a scuba tank, capacity 0.75 ft^3. What volume of ambient air was compressed?
What is the length of a 200 ft. steel tape having a cross : What is the length of a 200 ft. steel tape having a cross-sectional area of 0.004in2 and a modulus of elasticity of 30,000,000 lb/in2 that is standardized at a tension of 20 lb and a temperature of 68°F
Determine the volume of the spherical tank to be used : A spherical tank is being designed to hold 7 moles of methane gas at a pressure of 8 bar and a temperature of 50oF. Determine the volume of the spherical tank to be used.
What will be the surface tension effects if the tube were : A water column in a glass tube is used to measure the pressure in a glass pipe. The tube is 1/4 in. in diameter how much of the water column is due to the surface tention effects? What will be the surface tension effects if the tube were 1/8 in. or 1..
What is the ratio of the density of water to the density : At a temperature of 100oC and an absolute pressure of 8 atmospheres, what is the ratio of the density of water to the density of air?
Calculate the total mass emissions of particulates out : The temperature in the stack is 350 degrees F and the pressure is 725 mm Hg. If the total flow rate of gas out of the stack is 200 standard cubic meters per second, calculate the total mass emissions of particulates out of the stack in kg/day.
What was the original velocity of the ball : A 7 kg bowling ball strikes a 2 kg pin. The pin flies forwardwith a velocity of 6 m/s the ball continues forward at 4 m/s. What was the original velocity of the ball
Determine the number of completely mixed chlorine contact : Determine the number of completely mixed chlorine contact chambers each having a detention time of 30 min that would be required in a series arrangement to reduce the bacterial count of a treated effluent form 10^6 to 14.5 organisms/mL if the first o..

Reviews

Write a Review

Civil Engineering Questions & Answers

  What would the diameter corresponding to percent removal be

a standard reverse-flow cyclone with a length of 5cm has a cut diameter of 250 microns. at a flow rate of 10^-7 m^3/s, what would the diameter corresponding to 90% removal be

  Choose a pipe to be used as a tension member to resist

Choose a pipe to be used as a tension member to resist a service dead load of 10 kips and a service live load of 25 kips. The ends will be connected by welding completely around the circumference of the pipe. The length is 8 feet. Use LRFD.

  Determine force exerted by the hydraulic cylinder on boom

A hoist mechanism is attached to the back of a pickup truck. The crate being moved by the hoist shown below weighs 200 lbs. Note: Point A is directly above point B and the vertical distance between points A and B is 16 inches.

  Find shape factor in shear for a rectangular cross-section

The "Shape Factor" of a cross-section of a beam is defined as the fully plastic strength divided by the force or moment causing first yield. Thus the Shape Factor for bending is Mp/My and similarly for shear, is Vp/Vy.

  What are the tensions in cables ab and ad

The 20-kg mass is suspended from three cables. Cable AC is equipped with a turnbuckle so that its tension can be adjusted and a strain gauge that allows its tension to be measured. If the tension in cable AC is 40 N, what are the tensions in cable..

  Determine the work done by the gas on the bullet

Assuming the origin is placed where the bullet begins to move, the force (in newtons) exerted by the expanding gas on the bullet is 18000 + 7000x - 20000x2, where x is in meters.

  What is the volume and base diameter of the resulting pile

Soil falls from a conveyor belt into a cone shaped pile at a rate of 1000lb/min. The bulk density of the soil is 110lb/ft^3. The height of the pile is equal to the base diameter.

  Determine the length of chord connecting pc to pt

Given a horizontal curve of radius 1400 feet, a central angle= 46 degrees 21 minutes located at PI 50 plus or minus 00.00 on the centerline of a two-lane road with 12-foot wide lanes,

  What annual rate of return must the endowment fund earn

A permanent endowment at the University of Alabama is to award scholarships to engineering students. The awards are to be made beginning 5 years after the $10 million lump-sum donation is made

  Find water depth just upstream of high broad-crested weir

Find the water depth just upstream of a 1.5 ft high broad-crested weir in a channel 6ft wide when the flow is 18 cfs

  Draw the shear and moment diagram for a beam

Draw the shear and moment Diagram for a beam that is 10 feet long, supported on the left end by a roler, and the right end by a pin, and has a 1000 lb load placed in the center i.e at 5 feet.

  Determine the energy dissipated in the jump

A hydraulic jump forms in a horizontal trapezoidal channel. The base width is 4m and the side slopes are 45o. The depths upstream and downstream of the jump are 1m and 3m.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd