What will be the shear stress

Assignment Help Civil Engineering
Reference no: EM13210814

A trapezoidal channel is carrying water at a normal depth of 5.2 ft, the channel has a bottom width of 10 ft and side slopes of 2 H to 1 V. It is running on a slope of 0.005 ft/ft. What will be the shear stress in lb/ft^2 exerted on the channel bed by this flow.

Reference no: EM13210814

Questions Cloud

Explain titration of the excess unreacted edta required : Titration of the excess unreacted EDTA required 15.9 mL of 0.0220 M Ca2 . The Cd2 was displaced from EDTA by the addition of an excess of CN-.
Select the sentence that is punctuated correctly : Select the sentence that is punctuated correctly.
Calculate the angles made by f with the postive x : a force is specified by the vector F=160i+80j-120k N.calculate the angles made by F with the postive x y and z axes.
Prepare a five-year income statements : Prepare a five-year Income Statements and Cash Flow Analysis and prepare alternative scenarios that help potential investors understand the financial opportunities that the situation offers
What will be the shear stress : A trapezoidal channel is carrying water at a normal depth of 5.2 ft, the channel has a bottom width of 10 ft and side slopes of 2 H to 1 V. It is running on a slope of 0.005 ft/ft. What will be the shear stress in lb/ft^2 exerted on the channel be..
Determine the flow area : A rectangular concrete channel is 3 m wide and 2 m high. The water 20 deg Celsius in the main channel is 1.5 m deep and is flowing at a rate of 30 m^3/s. determine the flow area, wetted perimeter, and hydraulic radius. is the flow laminar or turbu..
Calculate the wet density in pounds per cubic feet : A small chunk of the original sample had a wet weight of 140.9 grams and weighed 85.2 grams after drying. Compute the water content, using the correct number of significant figures.
Estimate the wet density : A sample of natural glacial till was taken from below the groundwater table. The water content was found to be 52%. Estimate the wet density,dry density,buoyant density,porosity,and void ratio. Clearly state any necessary assumptions.
What is the allowable minimum length of the ramp : Using the ADA code, what is the allowable minimum length of the ramp base if base if it is 2 ft high and the code is 1:12

Reviews

Write a Review

Civil Engineering Questions & Answers

  Coefficient of friction-skidding resistance

Two passenger cars are traveling at 65 MPH on a highway moving in the same direction in the same lane. The cars are separated by 25 feet for every 10 MPH of their speed. The coefficient of friction (skidding resistance) between the tires and the r..

  What will the freeway density

What will the freeway's density and level of service be before and after the ban? (Assume that the trucks are removed and all other traffic attributes are unchanged)

  Evaluate the acceleration along and normal to the path

The velocity along a pathline is given by V (m/s) = s^2 x t^(1/2) where s is in meters and t is in seconds. The radius of curvature is 0.5 m. Evaluate the acceleration along and normal to the path at s = 2m and t = 0.5 seconds.

  Tangential component of the acceleration of the sled

Knowing that the coefficient of kinetic friction between a sled and the run is 0.10 and that the speed of the sled is 25 ft/s at B, determine the tangential component of the acceleration of the sled a) just before it reaches B, b) just after it pa..

  Find the rate of change in volume

A water tank has a height of 120m, and its area of cross-section is 2000m. Water is released from the tank and the water level drops by 1 meter every minute. Find the rate of change in volume.

  Horizontal motion of plunger and shaft

The horizontal motion of plunger and shaft is arrested by resistance of the attached disk which moves through the oil bath. If the velocity of plunger is v.

  Design a single angle strut connected to a gusset plate

Design a single angle strut connected to a gusset plate to carry 180k n factored load. The length of the strut between center to center intersection is 3m.

  Determine the required value of the mass

a 1 meter diameter cylindrical mass is connected to a 2 meter wide rectangular gate. the gate is to open when the water level drops below 2.5 meters. Determine the required value of the mass of the cylinder in kgs.

  Explain transportation network

Transportation network, A power generator at a dam can send 300 megawatts to substation 1, can send 200 megawatts to substation 2, and can send 250 megawatts to substation 2

  Determine the flow rate of the oil

Oil of a specific gravity of 0.75 is flowing through a 6-in pipe under a pressure of 15 psi. If the total energy relative to the datumplate is 8.0 ft below the center of the pipe is 58.6 ft, determine the flow rate of the oil.

  Survey with construction applications

The calculation and layout of horizontal and vertical curves should be done only by experienced surveyors and differential leveling measurements

  Practice autocad software package

To provide knowledge and practice AutoCAD software package for engineering activities.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd