What will be the final temperature in the tank

Assignment Help Mechanical Engineering
Reference no: EM13212604

a 1m^3 tank is to be filled using nitrogen at 300K and 20MPa. Instead of using a valve to throttle the nitrogen in the tank, a reversible turbine is put in the line to get some work out of the pressure drop. if the pressure in the tank is initially zero, and the final pressure is 20MPa, what will be the final temperature in the tank? how much work will be accomplished over the course of the entire process?

Reference no: EM13212604

Questions Cloud

Define a bimetallic strip of aluminium and copper is heated : Explain from a micro and macro perspective what would happen and what might be observed when a bimetallic strip of aluminium and copper is heated from 27 degrees to 327 degrees?
How should manager of largo publishing house adjust input : The Largo Publishing House uses 400 printers (workers) and 200 printing presses to produce books. A printer's wage rate is $20 per hour and the price per hour of a printing press is $5,000. The last printer hired added 20 books (per hour) to total..
Find the maximum temperature in wall : The heat transfer convection coefficient between the wall and the fluid is 500 W/m2.K. Find the maximum temperature in wall.
Compute the ph value of nh3 solution : Calculate the pH value of solution (a) after 10.0 mL of NH3 solution have been added and (b) after 25.0 mL solution have been added (Ka for NH4+ = 5.6 x 10^(-10).)
What will be the final temperature in the tank : what will be the final temperature in the tank? how much work will be accomplished over the course of the entire process?
Determine the control resolution for this robot : The linear joint (Type L) of a certain industrial robot is actuated by a piston mechanism. The length of the joint wehn fully retracted is 600 mm and when fully extended is 1000 mm. If the robot's controller has an eight-bit storage capacity, dete..
Find the cross-price elasticity of demand : What is the relationship between goods x and y? Explain carefully. Using income as your primary factor, identify what category Good X falls into. Find the price elasticity of demand. Find the income elasticity of demand. Find the cross-price elast..
Determine the net electric output : Water enters a hydraulic turbine through a 30-cm-dia pipe. The pressure drop in the turbine is measured by a mercury manometer to be 1.2 m. For a combined turbine-generator efficiency of 83%, determine the net electric output. Disregard the effect..
Explain what is the molar mass of the enzyme : Assuming the density of the solution is 1.00 grams/mL, what is the molar mass of the enzyme?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd