What will be the discharge through the pipe

Assignment Help Civil Engineering
Reference no: EM13545639

A pump having the characteristics given in figure 14.9 ( N=2133.5 rpm, n=35.6 rps, D=37.1 cm) pumps water at 25 degree C from a reservoir at an elevation of 366 m to a reservoir at an elevation of 450 m through a 36 cm steel pipe. If the pipe is 610 m long, what will be the discharge through the pipe?

Reference no: EM13545639

Questions Cloud

The only section remaining to be installed is a segment : A town is installing a new 10” main to carry drinking water. The only section remaining to be installed is a segment through the middle of town. However, the excavators discover an archaeological site. The town decides to split the main into two sect..
Determine the cop of the heat pump and rate : Refrigerant 134a enters the condenser of a residential heat pump at 800 kPa and 35 degrees celcius at a rate of 0.018 kg/s and leaves at 800 kPa as a saturated liquid. If the compressor consumes 1.2 kW of power, determine a) the COP of the heat pump ..
What contour intervals will be drawn if a 50ft interval : An area that varies in elevation from 463ft - 634ft is being mapped. What contour intervals will be drawn if a 50ft interval is used? Which lines are emphasized?
The mass center of the unbalanced disk of weight w is locate : The mass center of the unbalanced disk of weight W is located at G, which is a distance of R/2 from the center for the disk. In the equilibrium postition
What will be the discharge through the pipe : A pump having the characteristics given in figure 14.9 ( N=2133.5 rpm, n=35.6 rps, D=37.1 cm) pumps water at 25 degree C from a reservoir at an elevation of 366 m to a reservoir at an elevation
Find the operating points (q) for one pump : The pump curve for a given pump is represented by hp,pump=20 (1-(Q/100)^2) where hp,pump is the head provided by the pump in feet and Q is the discharge in gpm.
What is the minimum radius that can be cleared : A two lane hwy with 12' lanes is to be reconstructed to a design speed of 50 mph. Due to right of way restrictions, the largest distance that can be cleared from the edge of the road is 10'. What is the min. radius?
What is the tensile force on the weld per foot : Due to a leak in Pump Station 1,the Alaska pipeline is shut down briefly.The pipe line is half full.Assume the pipe is welded horizontally at its midpoint.What is the tensile force on the weld per foot? Assume Ø=40”and ?oil=53.55lb/ft3.
The average return period of the median value : The probability that, for a 2-year period, the peak flow rate will equal or exceed the median value in the second year, but not in the first year?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the exit pressure p2 if the friction head loss

Water ?ows at 6 ft/ s through a pipe 500 ft long with diameter 1 in. The inlet pressure p1= 200 psig, and the exit section is 100 ft ft higher than the inlet. What is the exit pressure p2 if the friction head loss is 350 ft?

  Determine what is the intrinsic permeability of coarse sand

The hydraulic conductivity of a coarse sand was measured in the laboratory permeameter and found to be 1.03x10^-2 cm/s at 25 degrees C. What is the intrinsic permeability

  Find maximum thickness t of the strip at allowable stress

A 900-mm strip of steel is bent into a full circle by two couples applied. Determine (a) the maximum thickness t of the strip if the allowable stress of the steel is 420 MPa, (b) the corresponding moment M of the couples.

  1 the us has produced the following quantity of gauges and

1. the u.s. has produced the following quantity of gauges and potatoes with the price of each listed in dollar

  Find tensile stress that will give probability of failure

The median value of the rupture strength was 300 MPa. The ceramic is to be used for components with dimensions l=50mm, b=d=5mm loaded in simple tension along their length. Calculate the tensile stress that will give a probability of failure of the..

  Calculate horizontal force required to hold hose in place

Diameter of the hose and the nozzle are .25ft and .1ft respectively. If the pressure inside the hose is 60 psig and the flowrate is 1.2 ft^3/s, calculate the horizontal force required to hold the hose in place.

  Ellipse construction via foci method

Ask question ellipse construction via foci method

  Disposal of excavated material

Discuss and use examples to explain the specific factors that you will need to consider when pricing the following items in the bill of quantities foundation excavation

  Determine the final temperature and mass of the air in the

Submarines change their depth by adding or removing air from rigid ballast tanks, thereby displacing seawater in the tanks. Consider a submarine that has a 700m3 air-ballast tank originally partially filled with 100m3 of air at 1500 kPa and 15oC. For..

  What is overturning factor of safety for building wind load

How many floors can be added to the building while maintaining the code required overturning factor of safety of 2.0 Assume the roof supports a wind load of 4 kips and all floors below support a wind load of 8 kips.

  Determine what force must apply at the ends to achieve

What couple moment does he exert. How much could he exert if he moved his hands to the ends so that his hands are 254 inches apart. What force must he apply at the ends to achieve the same couple moments as when he held his hands 18 inches apart.

  At what rate must pac be added to meet the proposed standard

A municipal drinking water treatment plant discovers that it has an unacceptably high level of the pesticide carbofuran and must develop a treatment technique to reduce the concentration to satisfy the relevant water quality standard.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd