What water mass flow rate is required report your answer

Assignment Help Mechanical Engineering
Reference no: EM13601718

Now consider the cooling process. It takes place in a heat exchanger (HX). Warm air. at 75 F, is flows into one side of the HX and exits at 60 F. Chilled water at 50 F enters the other side of the HX and exits at 55 F. What water mass flow rate is required? Report your answer in gpm (gallons/minute). The analysis you just performed assumes no heat exchange between the HX and its surroundings. Since the surroundings are at the same temperature of the building (nominally 72 F in the summer), this is not true. Assume a 5000 Btu/hr heat loss from the HX and compute a new value for the water mass flow rate. Again report your answer in gpm.

Reference no: EM13601718

Questions Cloud

The coefficient of static and kinetic frictions between a 3 : the coefficient of static and kinetic frictions between a 3 kg box and a desk are .4 and .3 respectively. what is the
The covariance of the returns between wildcat stock and sun : the covariance of the returns between wildcat stock and sun devil stock is 0.09875. the variance of wildcat is 0.2116
The nypd precincts in manhattan are numbered from 1 to 34 : the nypd precincts in manhattan are numbered from 1 to 34. if the variable precinct is included in a dataset about
On july 23 of the current year dakota mining co pays : on july 23 of the current year dakota mining co. pays 4836000 for land estimated to contain 7800000 tons of recoverable
What water mass flow rate is required report your answer : now consider the cooling process. it takes place in a heat exchanger hx. warm air. at 75 f is flows into one side of
The number of robberies in each precinct in 2009 is what : the number of robberies in each precinct in 2009 is what level of measurement?1. none2. nominal3. ratio4.
Jamaica corp is adding a new assembly line at a cost of 85 : jamaica corp. is adding a new assembly line at a cost of 8.5 million. the firm expects the project to generate cash
Elson corporation a retail fuel oil distributor has : elson corporation a retail fuel oil distributor has increased its annual sales volume to a level three times greater
The beta of elsenore inc stock is 16 whereas the risk-free : the beta of elsenore inc. stock is 1.6 whereas the risk-free rate of return is 8 percent. if the expected return on

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The lower end of the 30 kg slender rod is displaced a small

the lower end of the 30 kg slender rod is displaced a small amount and released from the rest. determine the natural

  Determine the magnitude of the load p

Knowing that the modulus of elasticity of brass is 105 GPa, determine the magnitude of the load P for which the deflection of the plug is 1,25 mm downward.

  What is the ideal mechanical advantage of the wedge

A hydraulic shear applies 2000 lb force to a wedge. It is used to shear plate steel to rough size. The shear has a 1/4 inch thick cutting blade with a 45 degree slope. What is the ideal mechanical advantage of the wedge?

  Find humidity ratio and relative humidity

A mixture of dry air and water vapor is at a temperature of 21C under a pressure of 101.3 kPa.The dew point temperature is 15C.(Ps= saturation pressure at 15C=1.7044 kPa;Pd=saturation pressure at 21C=2.4861 kPa) find humidity ratio and relative hu..

  Define a steel cylinder with an internal radius

A steel cylinder with an internal radius of 50mm is designed to carry a maximum stress of 400 MPs. It is subjected to an internal pressure of 80 MPs.(i) Determine the required wall thickness.

  You are designing a remote-area power supply based on a

you are designing a remote-area power supply based on a miniature wind turbine that is 20 efficient. meteorological

  Draw the block diagram of the uncontrolled seat

Draw the block diagram of the uncontrolled seat Plot the open loop displacement response of the uncontrolled seat to a step input

  Bullet a from west with a mass of 175g and speed of 550ms

bullet a from west with a mass of 175g and speed of 550ms and bullet b from east with a mass of 150g and speed of 200ms

  A six-station automatic assembly line has an ideal cycle

a six-station automatic assembly line has an ideal cycle time of 12 sec. downtime occurs for two reasons. first

  Determine the number of revolution by the disk

a disk has a mass of 4kg and a radius of 90mm, it is at rest when it is placed in contact with the belt, which moves with a constat speed (v =15m/s). knowing that friction is .25 between the disk and the belt. Determine the number of revolution by..

  Module fea - finite element analysisnbspquestion 2 method

module fea - finite element analysisnbspquestion 2 method to assess the value of your analysis outputnbspa what is the

  Explain the velocity of the ball when it reaches the highest

A ball with a mass of 0.25 kg is thrown vertically upward with an initial velocity of 10 m/s. What is the velocity of the ball when it reaches the highest point?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd