What torque is required to drive the disk at 760 rpm

Assignment Help Civil Engineering
Reference no: EM13544531

A flat disk spins within an oil-filled enclosure. Clearances between the enclosure to both sides of the disk is 2.3 mm. The disk surface (area subject to shear) extends from radius 10mm to 90 mm. What torque is required to drive the disk at 760 rpm (rpm is revolution per minute) if the oil’s absolute viscosity is 0.12 N s/m2?

Reference no: EM13544531

Questions Cloud

Determine the maximum height the projectile will reach : A projectile is fired up into the air at a speed of 161 m/s at an angle of 64° relative to the horizontal. Determine the maximum height the projectile will reach.
What would the manometer reading be for the same pressure : Two vessels are connected to a differential manometer using mercury (s=13.56), the connecting tubing being filled with water. The higher-pressure vessel is 5 ft lower in elevation than the other
What is the tree horizontal length of the recorded slope : A 100 ft steel tape of cross-sectional area 0.0025 in^2, weight 2.3 lb, and standardized at 68 degrees F is 99.992 ft between end marks when supported throughout under a 12-lb pull. What is the tree horizontal length of the recorded slope distance BC..
What would you expect the barometer reading : A scientist plans to build a water barometer. When the atmospheric pressure is 990 mb abs and the water temperature is 70 degrees Celsius, what would you expect the barometer reading (water rise) to be?
What torque is required to drive the disk at 760 rpm : A flat disk spins within an oil-filled enclosure. Clearances between the enclosure to both sides of the disk is 2.3 mm. The disk surface (area subject to shear) extends from radius 10mm to 90 mm
If the required compaction is 95 percent of the target how : Base course aggregate has a target dry density of 119.7 lb/cu ft in place. It will be laid down and compacted in a rectangular street repair area of 2000 ft*48ft*6in. the aggregate in the stockpile contains
Determine the force of gravity acting between them compare : Two particles have a mass of 8 Kg and 12 Kg respectively. if they are 800 mm apart, determine the force of gravity acting between them. Compare this result with the weight of each particle.
Evaluate the impact of these changes on ridership : If the elastic values of Bus service demand with respect to fare & headway are -0.35 & -0.7 respectively. A Bus service system which currently carries 56,000 passengers per day plans
The demanded is equal to the quantity supplied : At the equilibrium price, the demanded is equal to the quantity supplied. At any other price (called a disequilibrium price) there is either a shortage or surplus. Calculate the amount of the shortage at a price of$ 5.30.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Perception-reaction time on a roadway

An engineering student is driving on a level roadway and sees a construction sign 180 m ahead in the middle of the roadway. The student strikes the sign at 56 kph. If the student was traveling at 90 kph when the sign was first spotted, what was th..

  Determine how long do one have to escape

You are in an old spy movie, and have been locked into a small room (volume 1000 ft). You suddenly realize that a poison gas has just started entering the room through a ventilation duct.

  Explain how to plot the hydraulic grade line

Water is pumped from a reservoir whose surface elevation is 1390 ft to a second reservoir whose surface elevation is 1475 ft. The connecting pipeline is 4500 ft long and 12 in. in diameter.

  Determine the maximum torsional stress in the shaft and its

The propellers of a ship are connected to an A-36 steel shaft that is 60m long and has an outer diameter of 340mm and inner diameter of 260mm

  Find correct horizontal distance considering a gentle slope

A civil engineer used a 30-m tape in measuring an inclined distance. The measured length on the slope was recorded to be 459.20 m long. The difference in elevation between the initial and the end point was found to be 1.25 m.

  Hydraulic radius of the river

In that season, what are the hydraulic radius of the river, its mean velocity and volumetric discharge?

  Design of wastewater treatment plant for a community

Consider the design of wastewater treatment plant for a community wiyh average daily and peak hourly wastewater design flows of 2.0 mgd. The raw sewage has an average of 230 mg/l BOD5 and 260 mg/l of suspended solids.

  Determine the normal stress in each portion of the rod

A polystyrene rod consisting of two cylindrical portions AB and BC is restrained at both ends and supports two 6-kip loads as shown. Knowing that E = 0.45 X 106 psi,

  How to determine the diameter of a drilled shaft pile

Using 1630.56 kN as the ultimate capacity determine the diameter of a drilled shaft pile that would have the same ultimate capacity and depth embedment (11.5 m) using the FHWA method. Neglect shaft resistance. Use a F.S. of 2

  Determine what is the shear strain at the inner surface

a circular steel tube of length L=1.2m is loaded in torsion. If the inner radius of the tube is 45 mm and the measured angle of twist between the ends is 0.4 degrees, what is the shear strain at the inner surface

  Determine the average value of k in meter per sec

A stopwatch was started when h was 501 mm and read 17.6 seconds when h was 244 mm; the test was repeated for a drop from 254 mm to 97 mm and the time was 22.4 seconds.

  At what distance from the centerline

Air at 70 degrees Celsius and atmospheric pressure flows with a velocity of 22 fps through a 3-in diameter pipe (e=0.00015 in). Find the friction head loss in 75 ft of pipe.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd