What size reactor is needed for operation at same temperatur

Assignment Help Mechanical Engineering
Reference no: EM13705994

You need to hydrolyze 500 lb/day of an ester at an initial concentration of 5 molar in basic, aqueous solution. The ester has a MW of 120. The product must be 99% hydrolyzed. In bench top experiments at 40C, it is found that 50% of the ester hydrolyzes in 15 minutes, with either 1 or 5 molar starting concentration. A reaction for 8 hours hydrolyzes essentially all the ester. It takes one hour to empty the reactor, refill with reactants, and restart.<br /><br />A) What size reactor is needed for operation at this same temperature? (Answer in liters)<br />B) What size reactor would be needed for just 90% hydrolysis (answer in liters)<br />C) The above reaction has an activation energy of 12 kcal/mole. What reactor volumes are needed if we can operate at 80C?

Reference no: EM13705994

Questions Cloud

Gear is put in neutral on level road without wind resistance : The rolling resistance of a 1200kg car depends on its weigh as F = 0.006m x gravity. How far will the car roll if at 90km/h the gear is put in neutral on a level road without wind resistance?
Determine the work required to compress a spring : The force F required to compress a spring a distance x is given by F - Fo = kx where k is the spring constant and Fo is the preload. Determine the work required to compress a spring, whose spring constant is k = 37 kN/m, a distance of 2 cm starting f..
Determine the magnitude and location of the resiltant force : Freshwater is impounded to a height of 11 ft behind a dam as shown. Determine the magnitude and location of the resiltant force on the 4-ft by 4-ft gate.
Plate is supported by the spring and the rubber pad : The following suspension system has two support structures-a spring and a rubber pad. Vertical force F (N) acts on the moveable plate. The spring has a spring constant of k1 = 1000 N/m. The rubber pad has a spring constant of k2 = 20000 N/m. The rubb..
What size reactor is needed for operation at same temperatur : You need to hydrolyze 500 lb/day of an ester at an initial concentration of 5 molar in basic, aqueous solution. The ester has a MW of 120. The product must be 99% hydrolyzed. In bench top experiments at 40C, it is found that 50% of the ester hydrolyz..
Compute the heat transfer between the two locations : At a section where the diameter is 4 in, methane flows with the veloctiy of 50ft/s and a pressure of 85 psia. At a downstream section, where the diameter has increased to 6 in, the pressure is 45 psia. Assuming the flow to be isothermal, compute the ..
Determine the resultant of load system : Determine the resultant of load system shown below. Locate where the resultant intersects grade with respect to point A at the base of the structure
The mole fraction of ethanol in the boil up stream : A distillation column, as shown in the figure to the right, is a device used to separate components with different volatilities. In a specific process, a distillation column is used to separate a feed stream containing 0.4500 mol ethanol/mol and 0.55..
Paddle wheel and an electric heater operate in a system : A paddle wheel and an electric heater operate in a system. If the torque is 200 N-m, the rotational speed is 400 rpm, the voltage is 20 V, and the amperage is 10 A, What is the rate of doing work?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd