What should the heat flux

Assignment Help Mechanical Engineering
Reference no: EM131147888

You have been asked to design a vertical wall panel heater, 1.5 m high, for a dwelling. What should the heat flux be if no part of the wall should exceed 33?C? How much heat will be added to the room if the panel is 7 m in width?

Reference no: EM131147888

Questions Cloud

Calculate the expected flow rate in m3 /h : Calculate the expected flow rate in m3 /h. Neglect minor losses.
Analyze ford motor companys balance sheet : In a two- to three-page paper (not including the title and reference pages), explain the purpose of a balance sheet and analyze Ford Motor Company's balance sheet from its 2012 Annual Report.
Jim and polly pernelli try hedging with stock index future : Explain why the Pernellis would want to use stock - index futures to hedge their stock portfolio and how they would go about setting up such a hedge.
What is the maximum roughness height allowable for the pipe : The tank-pipe system of Fig. P6.49 is to deliver at least 11 m3 /h of water at 20°C to the reservoir. What is the maximum roughness height allowable for the pipe?
What should the heat flux : What should the heat flux be if no part of the wall should exceed 33?C? How much heat will be added to the room if the panel is 7 m in width?
How would the heat flux change : how would the average heat transfer coefficient change if ammonia, R22, methanol, or acetone were used instead of steam to heat it?
Outsourcing cool case study for marketing management : "Outsourcing Cool" case study for Marketing Management. Do you think consumers would buy Apple products if they were aware of the labor law violations of Apple's suppliers? How would this activity affect your personal buying habits for a product?
How many units should it order each time : One of its models is expected to sell 8,710,000 units in the coming year. How large should each product lot be if it costs $3750 to change production from one model to another. Assume that the manufacturer values each laptop unit at $190 dollars a..
Accounting information system : Write a project report on the given topic " ACCOUNTING INFORMATION SYSTEM:  A CASE STUDY ON MAJU JAYA SDN BHD"This whole assignment concentrates upon two facts. Firstly the usefulness of the accounting information system and secondly the characterist..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Assuming that both the turbine and the pump are isentropic

consider a reheat cycle with steam leaving the boiler and entering the turbine at 4 mpa and 400 c . after expanded in

  During a race the dirt bike was observed to leap up off the

during a race the dirt bike was observed to leap up off the small hill at a at an angle of 60o from the horizontal. if

  Crystal subjected to uniaxial compression

NaCl crystals slip on {110} slip systems. There are six systems of this type. Consider a crystal subjected to uniaxial compression parallel to z = [110].

  Determine the size of the contact patch the contact

determine the size of the contact patch the contact stresses and the maximum shear stress for a 40 mm diameter steel

  Determine factor of safety relative to shear stress theory

A component with a radius transition is attached to a rigid wall at point A. Determine the factor of safety relative to the maximum shear stress theory of the proposed material if it's yield strength is 90 MPa

  Assuming the variation of thermal conductivity of the wire

a 2 kw resistance heater wire with thermal conductivity k 15 wm-k diameter d .4 cm and length 50 cm is used to boil

  A 4 kw motor is driving an oil pump with an efficiency of

a 4 kw motor is driving an oil pump with an efficiency of 95 down a 10 mm diameter pipe. if the velocities of the fluid

  Determine the net work done per cycle

If the peak pressure and peak temperature of the cycle are 4.8 MPa and 2500, determine the net work done per cycle (kJ/kg) and the cycle thermal efficiency .

  What is the semi-major axis of the orbit

A satellite is in Earth orbit with an altitude at perigee of 555.0 km and an altitude at apogee of 1200.0 km. a. What is the semi-major axis of the orbit? b. What is the eccentricity? c. If the true anomaly is 160 degrees, what is the satellite's ..

  Calculate the work done by the gas on the piston

energy is added to a piston cylinder arrangement, and the piston is withdrawn in such a way that the quantity PV remains constant. the initial pressure and volume are 200kpa and 2m3, respectively. the final pressure is 100kpa, calculate the work d..

  Steam at 4800 lbfin2 1000 f enters the first stage of

steam at 4800 lbfin2 1000 f enters the first stage of asupercritical reheat cycle including two turbine stages. the

  Determine how long it will take for the casting to solidify

In the casting of steel under certain mold conditions, the mold constant in Chvorinov's Rule is known to be 4.0 min/cm2, based on previous experience. The casting is a flat plate whose length = 35 cm, width = 10 cm, and thickness = 15 mm. Determine h..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd