What should be on time of chopper to provide motor current

Assignment Help Electrical Engineering
Reference no: EM13285761

A step down chopper is to be used to supply power from 600 overhead wire to commutator motor on a trolley bus . The motor may be modeled as a generated direct voltage in series with a resistance of .2? and inductance of 25mH. The frequency of the chopper is set at 500 Hz.
1-When the bus is stopped , what should be the ON time of the chopper to provide a motor current of 150 A ?
2-What is maximum possible generated voltage of the motor for which a current of 150 A can be supplied ?
3-What is the average value of the supply current for the conditions of 1 and 2

Reference no: EM13285761

Questions Cloud

What is the internal rate of return for an investment : What is the internal rate of return for an investment with the following cash flows? Remember to net the flows of each year.
The compounds from benzene : Explain how you would prepare each of the following compounds from benzene:
Determine the resistance of the new wire : A wire that has a resistance of 5 is passed through an extruder so as to make it into a new,What is the resistance of the new wire
What would be the index value : Three stocks have share prices of $12, $75, and $30 with total market values of $400 million, $350 million and $150 million respectively. If you were to construct a price-weighted index of the three stocks what would be the index value?
What should be on time of chopper to provide motor current : A step down chopper is to be used to supply power from 600 overhead wire to commutator motor on a trolley bus . The motor may be modeled as a generated direct voltage in series with a resistance of .2? and inductance of 25mH.
Evaluate the molar mass of quinine : the freezing point of the solution is lowered by 5.10 °C. The freezing point and Kf constant for cyclohexane can be found here. Calculate the molar mass of quinine.
Estimate the phase difference between the sounds : Estimate the phase difference between the sounds received by your ears when you are facing 90° away from the direction of the source
How much should the investor be willing to pay for this bond : The bond issue in question has a par value of $1,000 and 7 years to maturity. How much should the investor be willing to pay for this bond?
Administrator take into account when hiring a marketing firm : What considerations should an administrator take into account when hiring a marketing firm? How would you choose a company to help you market your practice?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the thermal-equilibrium electron and hole concentration

Calculate the thermal-equilibrium electron and hole concentrations in a compensated p-type semiconductor. Consider a silicon semiconductor at T=300K in which Na = 10e16 cm-3 and Nd=3x1015 cm-3. Assume ni = 1.5 x1010 cm-3.

  Find the value of the supply current at the power factor

Calculate (i) the parallel capacitance C1 that would be required to change the power factor of the total load on the supply to 0.80 lagging and (ii) find the value of the supply current at this power factor.

  What operation is done to check if its is a negative number

In Mips when you use addi or any other commands in which you use a 16 bit value for a reg. value or address offset what operation is done to check if its is a negative number's two's complement or just a regular binary number

  Determine a suitable sampling frequency

Determine a suitable sampling frequency. Design a notch filter to remove the 50Hz component, paying particular attention to any assumptions you have made in the design.

  What is the distance fx between orders m and n

A double slit illuminated with light of wavelength 498 nm forms a diffraction pattern on a screen 45 cm away. The slit separation is d = 4196 nm. What is the distance fx between orders m = 17 and m = 16

  Calculate the total number of kbps needed in the adc

An analog signal has a bandwidth of 37 kHz and must be digitized in an ADC. The peak voltage is 7V and you need to maintain a resolution of 0.078V. Find the number of bits per sample and then

  Determine the bandwidth of the differential amplifier

According to the TL081 datasheet, the input noise voltage and current of TL08 are 25 nV/ÖHz and 0.01 pA/ÖHz, respectively. Assuming the circuit operates under room temperature, please find the output voltage Vout

  Calculate the losses in the transformer under the conditions

calculate the losses in the transformer under these conditions. losses and efficiency when the transformer delivers its rated power to a load having a power factor of 90%

  Determine the number of binary digits required to encode

A compact disc (CD) records audio signals digitally by usingPCM. Assume that the audio signal bandwidth equals15kHz. a) If theNyquist samples are uniformly quantized into L = 65536 levels andthen binary-coded

  What is the power received by the radio set with the antenna

A FM radio station transmits signals with circular polarization at 100 MHz center frequency. A vertical quaterwave monopole antenna is used in a radio set to receive this signal. If the average power density of the signal is 0.265pW/cm^2

  Design a voltage-divider bias network using a supply

Design a voltage-divider bias network using a supply of 24V, a transistor with a Beta of 110, and an operating point of IC = 4mA, and VCE = 8V. R2 = 7.5k. Choose VE = (1/8)VCC

  Determine with a resolution the values of r and l required

The enclosure is to be built to have an area A of 2000 ft^2. The cost of the fence is $50 per foot for the curved portion and $40 per foot for the straight sides. Use the fminbnd function to determine with a resolution of 0.01 ft the values of R a..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd